Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hello, Our application image became too large for TF-M and we're investigating the use of PSA Protected Storage without TF-M as described in NCS 2.6.0.
When writing a new...
Hi,
I encountered a modem fault (NCS v2.5.1, mfw 1.3.4, nrf9160DK). Here's a portion of the log leading to the fault:
[24:36:01.333,312] <inf> gnss: event NRF_MODEM_GNSS_EVT_PVT...
Hello!
I am a beginner and am trying out an MQTT example on my nRF9161 DK that I recently bought in my Visual Studio Code on Windows 11. I am aware that the sample application...
Hi,
I am able to get my CA certificate working using TLS for MQTT. but im not able to get the TLS Client certificate working.
I had created a client certificate as per...
Hello, I'm following along the nRF Asset Tracker guide and I'm on the step 'Create device credentials'
Running the command
' ./cli.sh create-and-provision-device-cert...
Hello support.
A new design is looking at using nRF24L01+ to communicate wirelessly. I'm aware that this IC is no longer recommended for new designs, however, it's the one...
Hello,
I am trying to use the LTE modem serial example on a customized board that communicates an NRF9160 SICA B1 with an external STM32 microcontroller through the UART...
I am using the nRF52840 with NCS SDK v2.5.1. I tried to implement non-volatile storage in my application, and it is working on the DK board, but the code is not working on...
Hello,
I am using the DK Buttons and LEDs module to get the status of my button on the ANNA-B402C ( nRF52833 ).
I wanted to check if any debounce filter/mechanism software...
Hello,
as mentioned in the subject, I want to use single bank while CONFIG_BOOTLOADER_MCUBOOT=y. The reason is that the nRF7002 firmware is so large, it would cause an overflow...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I want to debug using the Logger module...
Hello,
I am developing a nrf5340 project based on the Nordic AWS IoT library. Connection is via Ethernet (W5500) and it works fine as DHCP and SNTP works fine and I can...
Hi,
I'm using nRF5340 Audio DK with a modified example code provided by (thanks again!), which integrates peripheral NUS through extended advertisement in parallel to...
Hi, I am using nRF5340 dev kit. I have successfully accessed external NoR flash (mx25r64) over qspi. But once I enable BLE with setting 'CONFIG_BT=y', I got littlefs mounting...
