Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Hello,
I am using the nrf21540 with the shield nrf21540ek; nRF Connect SDK 2.6.2 and the toolchain 2.7.0.
Currently I am getting the following warning on the log output...
Hello,
I am using nRF Connect SDK v2.6.1 and nRF Connect for desktop v5.0.2.
I am currently developing with the nRF21540 and for some tests, I want to use the RSSI Viewer...
I am currently working on a project using an nRF52840 with an nRF Mesh controller and have run into an issue when trying to perform Device Firmware Updates (DFU) using multiple...
I'm developing a BLE application on nRF52840, where several characteristics correspond to several parameters. I need to read and validate parameters stored in flash when the...
Hi
We are using the nRF52832 with the SoftDevice S132 V7.2.0. Recently, we had to enable the FPU whereby we have to re-evaluate the consequences of erratum 220.
According...
Hello,
This is a theoretical question rather than a problem:
Let's say I have 2 devices that need to communicate over standard BLE profile and every so often needs to...
I'm using SDK1.3 on a nRF52840 and running BLE on it. I'm using FreeRTOS under it and specifically non-preemptive scheduling. From time to time I do a scan using a filter...
After upgrading to NCS 2.7.0 I noticed the MX25R1635F (A very commonly used / well supported chip for zephyr) no longer enters deep power down. On further investigation, changes...
Hello,
I have several sketches from prototyping my project but It's occurred to me that the libraries used for some sensors are unique. I want to use the SDK connect examples...
we are facing an issue with our nRF5340-nrf7002 custom device where, after a reset, it takes approximately 3-5 seconds to enter the application. This delay seems to be occurring...
I am considering software that uses nRF52840, where one side will send advertisements and the other side will scan and obtain data from advertisements.
I am considering...
Hi,
I’m developing a BLE IoT product using the nRF52840 DK, where I need to send a payload of 60 bytes. In a previous response to one of my questions, I was advised to increase...
I have a requirement for PMIC which should include charging, sleep mode integration and should give simultaneously 2 outputs. One output should range from 3-5V the other one...
Hey
I have tried to enable and test coredump as shown in this example: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-2-debugging/topic...
My production board doesn't support UART, but we have SEEGER JLINK using RTT to debug with. I'm using nRF5_SDK_17.0.2_d674dde\examples\dtm\direct_test_mode project.
If I...
