Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
i have developed the VL53L5CX code with BLE nrf52840 and it is working fine but issue i have faced is the USB port Restarted Whenever Firmware Download Process Start below...
HI Nordic support team.
I have a question relate to TX power in ANT application:
- ANT Tx application using: ant_broadcast ->Tx
- ANT Rx application using: ant_continuous_scanning_controller...
I've been running a Central + Peripheral application. I can successfully scan for devices and get the advertising data.
However, when I try to connect, the code seems to...
I am running the Direction Finding Connectionless Beacon sample using my nRF52833DK to transmit CTE packets. I am using the u-Blox ANT-B10 antenna board to receive the CTE...
"I am using ncs v2.6.1 on VSCODE, and the following issues have occurred:
Issues:
- Existing build files are not visible in the application.
- New builds are possible...
The multicell loaction has been working fine for a long time. About 8 days ago, I started to receive an error when requesting the location through "Here"
Any help would...
I am working on an application for an LE Audio Broadcast sink on an nrf5340 Audio DK. I am using code from the nrf5340 Audio application (v2.6.0) for the le audio parts. I...
Hi! I'm new to using the Nordic products and I wanted to be able to power my Thingy 91 device without the use if the USB and with a separate external power supply. On the...
Hi there,
Currently we are developing our own system to drive WS2812B LED's using the NRFX pwm library. And the coloring and signaling works fine when it is in a bare metal...
Hi,
I am using nrf52840 and SDK17.1.0.
I need to calculate CRC16 for communication with an another module. I found that we have an API for that. I would like to know what...
We are planning to develop an Matter door lock which includes NFC/RFID, Audio, keypad and BLE functionalities used separately. I am considering using either the nRF52840 or...
I tried setting the VDD voltage in the 9161 DK to 3,3 V, but it remains at ~1,76 V.
I'm able to enable/disable the GPIO extender just fine, so at least reading & writing...
I have had great success developing a project based on the peripheral_uart sample. Now I am trying to add DFU over UART to that project. Specifically, I would like to add...
Hi,
I have the following minimal example:
main.c
proj.conf:
Now, when setting CONFIG_SERIAL=n my nRF52840DK drains about 3-4 µA, when setting CONFIG_SERIAL=y it...
I am attempting to use the automatic WiFi connection feature described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/wifi_mgmt_ext...
