Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,nordic team
In programming code with v2.9.0\nrf\subsys\bluetooth\conn_ctx.c
and found some bugs of mutex lock.For losing unlock result in lock forever bug.
The selected...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I just stumbled upon a potential issue after trying to figure out why I couldn't use 'softreset...
Hello, I'm having problems trying to make the MODBUS RTU Client code work on my board.
I'm devoloping with nrf Connect SDK v2.1.0, using Visual Studio Code.
The board...
I build the NCS 2.9.1 connectivity bridge with
west build -b thingy91x/nrf5340/cpuapp
when I try to flash that with jlink, I get
west flash -- west flash: rebuilding...
Hi I'm trying to get more insight about nRF7002 power supply requirements. My last question didn't get a follow up so I guess a block diagram of the internal power arch was...
What would happen if a battery were connected in reverse to the nPM1100? Would it cause damage to the IC, trigger any protection mechanisms, or result in abnormal behavior...
When Developing with nRF5 SDK, follow the Developing for the nRF52805 with nRF5 SDK - Getting Started - nRF5 SDK guides - Nordic DevZone 。
The Peripheral UART Example runs...
Hi Nordic,
I have a general question about kernel threads in the mesh stack. From memory, Bluetooth has its own thread in the stack I think. At some point in the stack the...
Hi,
As title, please help to share the required information for nRF52085 pre-design evaluation, thank you.
1. Reference schematic & layout file & guidance.
2. Design...
I've installed Visual Studio Code and nrfutil and nRF Connect and J-Link and managed to compile Blinky and flash the Thingy:91 X using the terminal:
./nrfutil device program...
Dear all,
I’m working on a project using the nRF9151-DK and need to implement frequent data transmission via LTE. My setup includes multiple I2C sensors, and I want to send...
Hi everyone,
I am getting this build error while I am trying to call a function from gpio.h in my custom code
Looking at my includes I see this
This is a really...
Hello,
I'm just starting with the Power Profile Kit 2. I've read all available documentation but I didn't find any information about the switch SW1 called 'POWER'. There...
Hi,
I'm using an nRF52810 on a custom board and I'm using softdevice s112_nrf52_7.2.0_softdevice.hex.
I want to write some information (just 4 bytes) to flash memory,...
