I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hi,
Our team is considering the use of SiTime MEMS oscillators, namely a SiTime SiT1615B, to help in harsh shock and vibration conditions our product will be used in....
Hi, I am using the nRF52840 DK with SDK 17.0.2.
I am working on a project using the ESB protocol. In my design, an ACK packet is transmitted to the receiver every 5 seconds...
Hello community,
I was hoping to ask 2 questions about my design choices when designing around the nRF52840, specifically the QIAA-R branch.
First, I am confused on as...
Hi,
The Light Lightness Control (LC) Server controls a single Light Lightness Server instance on the same device with a state machine. Is there any application that demonstrate...
Hello,
I am using Bluetooth mesh for a project. I have a central device acting as a provisioner, and node devices that get provisioned as normal through this device. I am...
Hi,
My company has a product that is in production using the nRF5340 SOC. We noted this morning that the product would boot and application code even if the nRF5340's reset...
Hi there, I've a following set:
nPM1300-EK (PCA10152 / 1.3.0 / 2025.18 / Serial no. 10B3B784F5316C68)
nRF Connect v5.2.0
nPM PowerUP v2.2.3
After launching nPM...
Hello,
I’m evaluating whether simultaneous uplink from two ESB nodes is possible on the nRF54L15 DK. The documentation mentions support for up to 8 pipes in a star topology...
Hello,
I am using the ANNA-B112 module with nRF52832 to communicate to an AD5940 AFE using SPI1. I am also communicating with three other sensors using I2C0. This project...
Hi,
We enabled the DFU and sent a new application successfully using the mcumgr command line program, but now we need to do this upgrade process using the host MCU.
...
I am working through an evaluation stage for a new product using nRD52840, possibly updated to nRF54L in the next development phase. The device is based upon Zephyr and being...
I'm getting the warning about CONFIG_BT_CTLR, but I've gone through and changed to HAS_BT_CTLR. I do have the following:
# Maximum Transmission Unit config
CONFIG_BT_GATT_AUTO_UPDATE_MTU...
Hi
I have a nRF52840 setup with external 32 kHz xtal and external 32 MHz xtal, supplied by 3.3V.
I would like the system to be in as low power mode as possible.
Each...
While testing BLE and USB individualy, they seem to work well. When there is simultaneous use, there appear frequent crashes/lock-ups in varius handlers.
BLE used: ble_app_uart...
