after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi!
I want to connect my NRFL2401 to my computer using BLE (v4.0.0) in order to collect data from a sensor. However, the «Start Scan» button is not functional. When I click...
Hi!
I am trying to subscribe to nrf cloud with topic " prod/<TEAM_ID>/<DEVICE_ID>/jobs/rcv". After that I get Disconnect event in the MQTT handler.
Topic "prod/<TEAM_ID...
Hello Everyone,
I am using NRF52832 in my project and in my project I want to charge the device through USB C. So when we plug in USB C into the device, the NRF52832 should...
I followed the directions for pulling down the nRF Connect SDK v2.0.2 via Toolchain Manager v1.1.3 in nRF Connect for Desktop v3.11.1.
I am using Ubuntu 22.04.1 LTS 'Jammy...
Hi,
I am creating a central code from scratch, using zephyr version 2.0.1. I want to know the central code contain all the zephyr rtos property like thread in background...
Hi All,
I am trying to communicate with IC MAX17201 using I2C interface. I am able to detect the IC and communicate with it.
When I read 8bit registers from the IC I don...
Hello,
nRF5340, NCS2.0.2, vscode.
\v2.0.2\zephyr\samples\bluetooth\periodic_adv
when TX and RX work on PHY_1M, two side work well.
but when TX side set BT_LE_ADV_OPT_CODED...
Hi,
Is it correct that nrf-sdk does not support (or have any implementation for) the "NV Counters" API in TF-M ? (needed for rollback protection in the Protected Storage...
Overriding the sdk_config.h configuration
Each define in the sdk_config.h file is a conditional define that is added only if it has not been defined previously so it can...
Hi - I have successfully built the Android Chiptool and Window Covering sample using NRF Connect SDK v2.0.2. I build them both using the same matter library that is installed...
I'm trying to investigate a HardFault that happens within half an hour of using our product.
Device is nRF52832, SDK is 17.1.0, SD is S132 7.2.0
So far, I never managed...
Hello,
I try to create and use my own device tree node.
For that I created a very basic yaml file:
compatible: "bat-measurement" properties: channel1: type: int required...
Hello,
This is a followup of an answered question: " How to get pairing/bonding to work in e.g. ble_app_uart".
The project, ble_app_uart_pair is the ble_app_uart example...
Dear Team,
We are using the following 32 MHz crystal from Epson (datasheet attached) on our nRF52810
The datasheet does not say the start up time for the crystal and...
I have two functions, which both try reading incoming data for a characteristic.
I would expect be the same address in both functions, since the p_ble_evt write struct should...
