after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
How can I adjust the BLE transmit (Tx) power, up to and including +8 dBm? I'm using nRF Connect SDK (NCS) on an nRF52840-DK .
I modified the throughput sample to reverse...
Hello, I'm trying to run the Ble Peripheral sample from "nrf\samples\bluetooth\peripheral_lbs" i'm using nrf connect V1.8.0 and NRF5340dk i followed the code in the github...
Hi,
I'am using the Ultrasonic Oxygen Senor with the nrf5340, the output is like this "photo" I want to calculate the concentration and the purity and with this values I...
Hello,
Is there any way to program the frequency output when sending a carrier wave to have a step size of around 1KHz? It seems that the default step is 1MHz.
Hi
I am trying to get the manufacturer data by ble_advdata_parse() as instructed in this case and this case , but it's not found in my SDK14.2, so how can I get the manufacture...
It's not possible to proceed a firmware update of matter light switch example on nRF5340DK.
I use following SDKs / Repos
nrfConnect SDK v2.0.2
standalone zephyr SDK...
Hello,
I have a component (AMC1306) in which I input a signal of at least 5Mhz. When this signal is triggered to this component, it sends me back data at this same speed...
Hi, I am trying with coap_client/server example programs on a custom board. I created a custom board for Zephyr and it is compiled without errors. I have a single button switch...
Module: nRF52832
Implemented pairing for ble_app_UART (NUS). However, I can connect with ble_app_uart_c, which does not have pairing implemented. Please tell me how to prevent...
I've just updated to the new V4.0.0 of the nRF Connect for Desktop BLE app. I'm trying to set it up as a server with CTS (but with both Current Time and Local Time Information...
Hi
When using external JLINK to download programs to 52840DK board, how should power supply, or how should configuration; What problems should you pay attention to when...
Hi there,
I found a ticket that involves the ticker and mayfly documentation, but the link mentioned in the answer was lost.
devzone.nordicsemi.com/.../is-there-tutorials...
I understand that this flag is for advertising in low duty cycle, however, how are the actual parameters (i.e., advertising interval) defined for this mode?
Hello there,
I am trying to work with the sample application named "radio test" for performing FCC testing with our hardware. However, I am not able to successfully build...
Hello,
I am using nRF Connect SDK 1.8.0 on the nRF52840. I want to limit the amount of time that a peripheral can connect to my central 52840. On connection start I initiate...
