after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I'm looking for some documentation for both projects. While there inline documentation and example projects are existing, I couldn't find any javadoc (or similar,...
Hi,
I want to use two SPI instances (0 and 1) in my project. I am able to modify the example SPI project to use 2 SPI instances as in the code below and setting #define...
I'm trying to get the ADC running on an nrf51DK, however whatever configuration I use it always outputs a value equivalent to ~0.6v input. I've tried with the basic ADC example...
I bought a product with NRF52840 as MCU. Now I want to communicate with other devices over RS485. So I had to make some changes. I have the following questions and hope to...
i try to build simple hello world program in c++. it successfully compile just yesterday, but somehow it fail to compile now. on the log it seem to use /usr/bin/c++ to compile...
The following code snippets produces Error code 0x0005 when trying to update a characteristic value via custom characteristic programming nd connected to nRFConnect app: ...
The nRF52833 datasheet lists a number of pads as "N.C." however I could not find anything in the datasheet about what to do with these pads. Is it safe to route traces over...
hi
I would like to use BLE Mesh to control my products. I would like to build a mesh network in advance, install a provisioner and automatically provision the nodes when...
I'm working with a lwm2m client using t he LwM2M client utils library to connect with a lwm2m leshan server.
Everything works great with LIFETIME = 30sec (default setting...
Hi:
There are two BLE architecture can be used on the nRF5340:
Split the Bluetooth LE Controller and the host part of the Bluetooth LE stack and run them on different...
Hallo Team,
I am using nrf45340 Audio DK to evaluate Bluetooth LE Audio application example.
For experimental purpose, I am using SBC codec. I have been following instructions...
Hello Nordic support:
We encountered a problem when downlaod the firmware for the nRF9160 with jlink nrfjprog program. Most our nRF9160 module can download firmware OK just...
Hi Nordic Team,
Working Environment:
nRF52832 DK, nRF17.1.0 SDK, Keil uVision 5 IDE, Windowns10 pro PC.
I am working on ble_app_uart.c Peripheral example.
According...
Hello,
the git version in ncs\toolchains\v2.0.0 isgit version 2.26.2.windows.1!
That prevets me from using git credental-manager-core in nRF Connect 2.0.0 console in Visual...
Similar to t_m's post here (only in a different SDK), I am trying to generate two PWM signals (motor1_fwd_pwm & motor2_fwd_pwm) in 180 degrees phase shift in respect to each...
