Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have two boards, a Thingy91 with "nrf9160 SICA B0 1924AP" and a nrf9160dk with "nrf9160 SICA B1 2110AM". Everything works as expected on nrf9160dk but on the Thingy91 shell...
I create an app timer for spi communication at 1s.
The I noticed a strange phenomenon.
You can see the 13uA is in sleep mode, when the app timer timeout, CPU wake...
Hi All,
I had a MCU to connect nRF52840 via UART and nRF52840 is used for BT central function.
I need to know the command to control nRF52840 and what function should...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising. Since there is no example of "pure" extended advertising...
Hi Nordic team,
I am working on a project with one central and several peripheral BLE devices. The peripherals are moving randomly, is it possible to detect the event...
Hi, recently testing nrf9160 SMS example, but seems not working in both Send/Receive
I confirm that SMS is valid in my SIM Card, I put it in my mobile phone and verified...
Can you please explain how the %XCOUNTRYDATA command can speed up network selection in a new location? Does the modem perform a general scan on all bands to determine the...
hello , I am working spi with softdevice(i.e., bluetooth). here spi master is nrf52 and spi slave is ad9837. the spi interface code works fine without soft device(i.e.,ble...
Hello, we are developing a keyboard with two types of connections, via USB and Bluetooth using the nRF52833 chip.
We have all the firmware developed in Arduino since it...
Hi,
I am trying to compile the cfb sample as provided in v2.0.0.
my overlay file is as follows
and my prj file
When I try to build, I get the following error...
is there a way to change the target device to nRF52820 (PCA10100) in segger embedded studio? initially configured to nRF52832 when we started our setup (nRF Connect Desktop...
I want to design a general module. Is it feasible to design the schematic diagram in this way?
1.VDDH is powered by external power supply, is that ok?
2.VBUS is powered...
Hi,
We want to check how changing system voltage affects on GPS reception, for that we need to know the RSSI of each satellite the model use.
I know I can get the C2N...
