Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi there,
As the title says, I only get an all white window whenever I open an app in nRF Connect for Desktop (this happens for all apps).
If I try to reload the window...
I try to get the Direct Test Mode App to work on a Windows 10 Notebook. (for System Details see attached system report and verbose logfile).
Software versions:
nRF Connect...
Hello,
I'm using the PCA100095 NRF5340 development board and developing with the NRF Connect extension for VSCode v2022.3.104 .
When attempting to use the CMSIS intrinsics...
Hello,
In my project i am using nrf52840 with custom board, here i am using BLE UART to send the data from the mobile to device and sending data from another sensor board...
I would like to add Just Works security to our battery service (BAS). However, I could not find such a setting anywhere, so I looked into it and found that in bas.c BT_GATT_SERVICE_DEFINE...
I am troubleshooting a board with no working RF. On looking deeper it appears that the HFCLK is not starting (NRF_CLOCK->EVENTS_HFCLKSTARTED is never set).
This is on a...
Hello,
I am currently working on the NRFX QDEC library with a decoder to be used with a servo motor.
We manage to initialize and enable the QDEC and IRQ and we get...
Hi,
I am facing a problem in adding a power down feature in my application, the details of the application are as follows,
I am using the sensor server example given...
Hey guys,
I have a small concern and decided to ask here, as i was not able to found answer neither in zephyr or nrf sdk docs (not even sure which one apply to my question...
I use the DF example.In Rx.i use both nrf52833 boards as test.i use NCS 1.9.1.
In rx,i use the silab's 16 antenna array for receving antenna array.
because it has 16 antennas...
Topology:
Raspberry Pi A Raspberry Pi B
|(USB connect) |(USB connect)
nRF52840 dongle A )))) Thread (((( nRF52840 dongle B
Software:
nrf52840-dongle: ot-rcp.hex...
In the online power profiler for nRF52832, when I look at the advertising (Tx/Rx) power consumption I see that if I set the Tx payload to 0 bytes the Tx time modeled is 128us...
Hello,
In my project i want two use two UART as off now i am using app_ble_uart example since by default 6,8 is tx and rx pins respectively. so overall application of my...
Hello everyone
I am working on nRF52DK devkit. I want to check the SPI waveform. Actually I want to interface waveshare e-paper display (1.54 inch) For that i used GFX...
