after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am working with nRF52833 DK with nRF Connect SDK. All was going great until I had to add a GNU GSL library. I need it because I need matrix multiplications with complex...
Hi,
We are working on a custom bootloader/DFU and is going to use USB CDC to perform DFU and some data transfers for version information. We use the USB CDC library both...
Hello,
SD: 122
part nrf52833
I need to do the following:
a. scan for advertisements containing a particular MAC address without connecting. This works.
b. the...
Are there any convenient ways to debug BLE connectivity issues? I have the service up and running but the connection on nRFConnect App doesn't quite go through: it remains...
Hello,
I work with the nRF5340 and want to use I2C0 (1-3 is reserved for other sensors in my project ). I already use I2C2 for a sensor and this works fine.
To use the...
Sorry I'have a question about the certification process of a BLE in a custom board.
I see that with zephyr that I can define a custom board derived fron nrf52840dk. If for...
I powered the DK up and the LED's would light corresponding to the button that was pushed.
The D drive would come up, so I drug the heart rate demo (hex file) to the drive...
I was trying to follow the video to create a project with VS Code. After I click the Create Application buttion, there is nothing happens. It only create a Folder with APP...
Hi,
I already read all similar ticktes but none of them does solve my problem.
i'm using nRF Connect SDK (NCS) with a custom board equipped with nRF52833. To implement...
Hello, I am considering using OpenThread mesh network for an application. I need to know if it is possible to blacklist/remove a device connected to the mesh network from...
Hi Dev team,
I am using the Thingy91 for my development project. I have noticed 1 peculiar issue and wanted to ask for suggestions regarding it.
I had deployed a Thingy91...
Hello there,
I am that newby in the vs code dev environnement. I use the XM122 from acconeer to perform radar measurement. The soft provide by Acconeer compiles and works...
Dear Community;
I am trying to port this code that was made for an nrf52 to an nRF9160. I have a 4.99K pull-up resistor between the data line and VCC.
This is my ds18b20...
Hi, Is it possible to increase the size of the buffer for the UART IRQ RX function such that it receives more than 8 bytes at each interrupt? Currently I am trying to send...
