after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi everyone,
I have setup a Bluetooth Mesh network of 5 Light Control Server Nodes and 5 Low Power Nodes that have friendship with eachother.
All nodes publish and subscribe...
I'm facing the requirement to save few kb of data in flash and process it over time. Because none of the standard mesh models fit, a custom mesh model will be the only option...
Hey,
I encountered a very strange problem while I was trying to connect from nRF52832 (as a central device) to my nRF52805 as a peripheral. If I am trying to connect to...
Hello,
I am working on a custom development board that is using the nRF52840. After programming the nRF52840 on the board with Soft Device s140_nrf52_7.0.1_softdevice.hex...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
The separation of flash memory into a region for the application core and one for the network core on the nRF5340 seems rather cumbersome and error-prone.
I'm especially...
Hi,
will qmi_wwan or gobinet driver be available for nRF9160? PPPD is not available. It is quite a limitation in use to miss ethenet interface based connectivity.
Regards...
Hi everyone, I’m have a wired network of 1000 devices (relay switches) that I’ve been tasked to upgrade to wireless.
Devices are inside a warehouse, about a pallet apart...
Hello All,
I am developing product using nRF52840 Dev-kit and SDK 4.1 for zigbee and thread.
I have created the new solution using tool chain - C:\Program Files (x86)...
Hello,
I'm using the NRF52840 with the NRF5 SDK v15.3.0 and S140.
I was trying to include the nrf_fstorage library into an existing project. The problem I experienced...
Hello,
I modified a sample app "blinky" on segger, to include main.cpp instead of main.c Then when I built, I got a compile time error stating in main.cpp "void main(void...
Hello.
I'm looking at options for a BLE device that has fairly small application requirements. It would essentially be a button, so the peripheral blinky example would make...
Hi Nordic!
We are gonna do pre-compliance testing of our custom board, with mounted nRF52840 and nRF9160 SICA B0.
We are looking for any software available from Nordic...
