Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I'm using the Azure Iot Hub example on a Thingy91 and am having issues with certs generated from a Linux environment. Everything works just fine with and without...
Hi ,
We are using nRF52832 IC for our project, Using BLE and PWM peripheral.
We are getting 1.28mA power consumption in the sleep mode.
As per the datasheet it should...
Hi, I built the lighting-app( Link ) and run on nrf52840 DK. Then, I tried to replace the serial shell console with RTT shell console. I append the configs below to the prj...
I am using my custom board , it is usually powered with a dc supply and I can program it easily. My chip is NRF52811.
When powered with a Cr2032 the segger studio says id...
Hello!
I have formed a Thread network and I am trying to ping an external IPv4 address and that request is not being forwarded to the border router.
My OTBR is a Raspberry...
Hello I am developing an application based on the "ble_thread_dyn_mtd_coap_cli" example. To create a Thread resource, I see that the "otCoapAddResource()" function is called...
Hi,
we are using NRF9160 based Custom board with Zephyr,
I want to track the Current time in IST format and i need to generate an event to DPPI on particular time (ex...
I might be missing something obvious here, but when the device is flashed (via SES), the application works correctly. When the device is power cycled or reset due to the watch...
I already flash the ble_blinky example to the nrf52840-dongle using nrfconnect desktop. The question is it is possible to do DFU OTA via Bluetooth without nrf52dk or nrfconnect...
Hi,
Can mocks fully compensate for C++ standard features.? Is it recommended to write C++ code in nCS project by using these mocks.? What is the support for C++ operator...
Recently I develop products on nRF5340, I plan to make the full BLE stack run in the net-core, and app-core only runs application. It involves data exchenge between net-core...
Hello,
We have a application with soft device on nrf52832 with SDK 15.3 with 60 uA power consumption. It works as it seems for now.
We wanted to add DFU buttonless feature...
Hi,
We were using Nordic HAL for FEM modules to drive our PA/LNA using nRF52840 on zephyr (no NCS). It was only a basic configuration, where the PA and LNA pins were selected...
Hi.
I have a quick question regarding the RSSI Value of Messages sent in a Bluetoth Mesh Network.
So my question is: How exactly is the RSSI Value defined and how does...
