Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi ,
I had done the user guide on https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/ug_matter_configuring.html#ug-matter-configuring , could you please tell...
Somehow it seems the interface MCU of my PCA10040 DK got confused. I cannot use the JLINK to the nRF any more, and the JLINK drive (in Windows 10) does not show up. LD5 stays...
Hi,
1. I want to know the minimum delay time of BLE data transmission
2.How should this time be calculated
Thank you for all your assistance. Kind regards, Peter.Mi...
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello Nordic Devzone,
I am currently attempting to generate 8mhz clock output to a gpio pin on the nrf5340dk. I have found previous posts about utilizing the gpiote, timer...
Dear Members,
How can I find the cause of
<error> app: Fatal error ?
I can't see an error code ?
Is it possible hardware error because voltage surge ? Can capacitor...
When I set NRF_LOG_ENABLED true, the RTT log can be output without any problem, however, the scanning or advertising activity stop immediately.
I found there is something...
Hi,
I am trying to find Get and set the RTC timer api inside Nordic SDK "nCS\v1.6.1\zephyr".
Could you please help me where I can get these api.
Thank You!!
I got up to this stage while trying to evaluate the module...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk_gsg%2FUG%2Fnrf91_DK_gsg%2Fintro.html
There...
Several place refer us to the SoftDevice Release Notes; eg
https://www.nordicsemi.com/eng/nordic/Products/nRF52832/S132-SD-v5/58987
http://infocenter.nordicsemi.com/topic...
Hi,
I have nRF52840 DK with nRFConnect SDK 1.6.99
Compiled and run on nRF52840 boards:
F:\_Develop\ConnectSDK\ncs\zephyr\samples\bluetooth\periodic_adv
F:\_Develop...
NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
What does m_ble_observer stand for ? i don't see any explanation in the whole project...
According to the Overview of this sample, the sample supports the provisioning of the IoT device using "Azure IoT Hub Device Provisioning Service (DPS)" to an IoT hub; and...
I am developing firmware for nRF52811 and I can't get UART working.
Sending data over TX works fine, but every time I try to receive something from RX, I get an error. ...
