I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I am facing following compiling issue while integrating the buttonless DFU to ble_app_uart code.
I have done whatever this case has instructed. Still i am getting...
I have set APP_ADV_INTERVAL to 100ms. Now when my device is rum=nning i want to manually change it say to 1000ms/300ms.Kindly assist how can this be done for ble_app_beacon...
I would like to use the flash in legacy way. My application collects data in small chunks and I would like to store it in a continuous area.
The recommended flash manager...
I succeeded in implementing the desired function using the NRF52832 development board.
I had to modify the project to include the NUS function of NRF52810. However, it has...
Hello, in zephir/include/drivers/can.h, in can_set_bitrate there is an error - you define local struct can_timing timing, but timing.sjw member wasn't initialized nor later...
In a previous post Related post it was mentioned that the below posted code would allow for a transmission of 20 bytes. However when I try to run this code I see a reported...
Hi everyone,
So I am having this weird behavior when i try to use the PWM with pin(1,9). In my case, i want to do pwm with a number of pin most of them are in port 0 like...
Hi support team,
We're planing to implement the scenario like this. In the mesh network, there are a few LPN nodes (i.e., 10 nodes) and one server node(non-low power node...
Hi,
Just need a quick checking on this.
Currently we using nRF5 SDK, after production, is it possible we OTA update the firmware which using nRF Connect SDK?
This...
Hi,
I tried to build and programm this DTM example from this SDK example: ncs\v1.6.1\nrf\samples\bluetooth\direct_test_mode
I got this following error. Do you know where...
Hi,
With the NRF Connect / NCS SDK, I can build the asset_tracker and serial_lte_modem without issue.
I want to make my own project, so I copied asset_tracker entirely...
Again I am asking a question I should not because I cannot find it documented.
I get a pairing request from the central. I need to respond with sd_ble_gap_sec_params_reply...
Hello.
Now, I'm trying to make a Beacon with updatable Major Value, based on sample 'ble_app_beacon'.
I'm not really familiar with BLE and Nordic device, though...
I...
Hi,
We have created GATT servers and tried to connect with one MOBILE APP.
But, we failed.
Although, we could able to connect with standalone BLE, but once we tried...
