after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
As reported on Discord, there is a bug in drivers/serial/uart_nrfx_uarte.c that leads to failing compilation:
zephyr/drivers/serial/uart_nrfx_uarte.c: In function 'cbwt_uarte_async_init...
Hello,
I am following Lesson 9 Exercise 6 of the Dev Academy nRF Connect SDK Intermediate tutorials ( https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
SDK:nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_hrs\pca10040\s132_with_dfu\arm4\ble_app_hrs_s132_with_dfu_pca10040
Our product encountered a problem with DFU...
I use an nRF5340 and nRF7002 on a custom board. My firmware is stable on the nRf7002-DK, but crashes on my custom board most of the time (mostly when connecting to the Cloud...
Hi Nordic Support,
I'm having trouble getting my Onomondo or Conexa SIMs to connect to the network and would appreciate your help.
Device: Nordic Thingy91X (nRF9151...
We are running a custom board with the nrf52840 mcu on the legacy 17.1 nrf sdk. external flash IC is AT25FF321A
On a small portion of our boards (maybe 1 - 5%) we are noticing...
Dear Technical Support Team, I am currently developing with the nRF54L15-DK development board, using the official Nordic channel_sounding_ras_initiator example project.
...
Hello,
Our product has reached the final mass production stage, but we need to add a lock function to prevent erasure and access to the programming/debug port. nRF54L10...
I am using the nRF52833 DK and a Nordic-designed antenna array (12 antennas with 0.02m spacing) for an AoA Direction Finding project. I obtained the IQ data using Direction...
SW version :2.4.0 HW revision: nRF52833 development board, PCA20054 Direction Finding Antenna Board 1_0_0 I use the routine director_finding_central and director_finding_periopheral...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you.
I just want to explore on nRF52840 BLE section. I was not able to detect the device...
Hello! I have 126 kB MCUboot partition which I'd like to make immutable (write protected so it can't be corrupted). I have serial-recovery, KMU key handling, debug optimization...
When building applications/hpf/gpio with -DSB_CONFIG_HPF_GPIO_BACKEND_ICMSG=y on nRF54L15 DK (NCS v3.2.4), the build fails with error: '__device_dts_ord_DT_N_NODELABEL_ipc0_ORD...
Dear DevZone Team
To detect possible TWI slave devices connected on a TWI bus, we want to scan for device addresses and check if they are being acknowledged.
In the twi_scanner...
