Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello.
I had LC3 access granted.
I can access nrfconnect/sdk-lc3 on my web browser.
However, with bash, I get the following error and cannot build nRF5340_audio.
...
Hi Mate,
I have very small issue that is when i am trying to link config_bootloader_mcuboot=y in zephyr application the program is not flashed. I need to run zephyr application...
I was curious if there was a delta firmware update file to go from 1.3.1 to 1.3.0 on the nRF9160. Most of our business is in North America and we use a carrier who requires...
Hi all,
I'm trying to use the nrf Connect SDK and configure PWM to use in one pin from nordif nrf52DK. The final chip will be the nrf52810. I have configured the builder...
Hello,
I want to use pc-ble-driver WITH an EV-BT8400XE.
I develop with SDK15.3 (last compatible version of SDK for pc-ble-driver)
I am successfully able to use pc-ble...
Hey all together,
I'm using nrf Connect SDK 2.0.0 and want to place a variable in flash at a predefined location. The reason is, that I need to read the information stored...
Hi,
I'm setting up nRF Connect SDK according to this instruction ( http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html) and Getting Started...
Hey,
in our project the nrf is acting as the central and connecting phones.
As part of the connection process:
1) We check if the phone is bonded in the nrf.
2) We...
Hi,
I'm on NCS 1.8.0 and I've successfully built and run the peripheral_nfc_example sample. Printed logs when reading NDEF message using a smartphone
When I came to...
I have a nRF52840-DK that stopped programing.
As a starting point to get it back to work, I reflashed the Interface MCU Firmware.
It is correctly detected by J-Link Configurator...
Hey Nordic,
My project is based on "ble_app_uart" and "ble_app_uart_c" examples. I modified them to some extent. You can download them from here .
Normally, I can write...
Hello!
On 3 and 7 of August my employee directed to you several questions regarding NRF. Case ID: 293339
Can I at least urgently receive the answer for the question in...
Hi,
We need to test our product for reliability when it comes to BLE connection in the vicinity of other BLE and WiFi devices. Do you have any suggestions on how to perform...
Hi all,
I am trying to use the bt_disable functionality on Adafruit Feather sense which has nrf52840 to restart a connectable BLE Service. The first call to bt_le_adv_start...
I'm developing an application using the NRF52840. I'm using the ADC, and there may be times where the signal to be measured is up to 1.8V, but the NRF52840 is not yet powered...
