Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
We are looking at how we software upgrade the device during its lifetime and assume that a bootloader will be required on the AP and the NP to allow us to load a new...
Hi Nordic,
I have learned about both the DTM and radio_test example source code. For our prototype tests, I think the latter may be better for us.
I have tried to wirte...
Hi
Is there a possibility to update the bootloader himself over the BLE DFU?
I have a new bootloader with a bigger size (MemoryMap changed) and I am wondering if I can...
Hello,
The following error message appears when the original code "asset_tracker_v2" under NCS 2.0 is compiled with vs code IDE,
Can anyone give me some comments? Thanks...
Hello,
I'm just trying to run the LTE_BLE_GATEWAY sample program and I've flash all the nessesary firmware onto the nrf9160dk baord. However, when I turn on the nrf52, it...
Hi,
I am building the CoAP client and sever example programs on a third party module (Reytac MDBT50Q). I am using Reytac dev board MDBT50Q-DB-40. Unfortunately the example...
Hi all
Can the NFC tag of nRF52832 be integrated with multiple cards？
Such as t he access control card of my dormitory and my home can be replaced by one card
Thanks...
I use the connected mode of DF, i use the two receiver,one transmiter,but when i flash the procedure to my boards.i find that only one receiver can get the IQ samples.how...
I am trying to port some code I wrote for Gazell, which I guess acts more elegant since it uses PPI, a workqueue, timeslots, etc. I have an ESB connection in which I receive...
Hi,
I am currently developing with the nRF52 DK (nRF52832 SoC) and the nRF52833 DK (nRf52833 SoC). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr...
HI,
I'm using nrf51822 and Gazell protocol.
from the RM, i get that the combined length of S0, LENGTH, S1, and PAYLOAD cannot exceed 255 bytes, which i think i can set the...
hello everyone, recently I entered the world of nordic,
and I have been testing some of the functionalities, of one of the devices,
specifically the nrf5304 dk model,...
Hello,
I created a device on AWS and corresponding certificates/shadows on the us-west-1 server. I'm able to successfully connect and send to this endpoint, but want to...
Hi Sir / Madam,
May i know if there is any layout guidelines that available for nRF5340-QKAA?
Appreciate if you could help to provide to ease the development of the...
