Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello!
I was wonder if it's OK to input voltages above the ADC Reference (0,6 V) to the SAR Core, while keeping within AIN pins well within 0 V and VDD.
We're measuring...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
Hi Friend,
We have a project using SDK16 and softdevice S140. We want to generate a looping output of 60ms 2.4GHz OOK and 500ms BLE scan. Ported 2.4GHz OOK from radio_test...
Hi, I'm Leo.
These days I'm learning BLE.
First, I'm using nRF Connect SDK(NCS) v1.9.1, S140, nRF52840 DK board.
I need to use SPI to control UWB transceiver(DWM3000...
Hello,
We've a design/arch question about the performance of nRF52840 device (dongle/EVK).
In our system, we've a PC connected to a PTX that communicates with multiple...
Hello,
I am working on BLE Mesh using SDK nrf5_SDK_for_Mesh_v5.0.0. I am using light_switch example for BLE Mesh client and server. I am using custom hardware for Mesh client...
I just finished successfully running the azure_fota and azure_iot_hub demos on my nRF9160DK. In a completely separate project, I am now attempting to adapt the TMP116 sensor...
Hi,
We're using Nordic Connect SDK V1.8.0 & nrf 52833 chip integrated on BL653 hardware & have some queries regarding logging SDK related data, following queries
What...
With an earlier version of NCS I could set the sda and scl pins using an overlay file:
boards/nrf52840dk_nrf52840.overlay:
With NCS 1.9.99 I get this error:
...
Hi,
I'm using the nRF52840 on a custom board along with an ESP8266 (ESP-12S) Wi-Fi module.
The ESP module prints out a bunch of information at a weird nonstandard baud...
I am having trouble setting up DFU over BLE in nRF Connect SDK. I am using NCS 1.9.1. I have followed these instructions with my own project on both the nrf52840 devkit and...
Dear All,
We are developing a device based around nRF52840 on a rigid-flex custom PCB that is mounted inside an anodized aluminum cube with one face covered with plastic...
Hello, I'm trying to get an LPN to unprovision itself based off of an external command. I tried to base it off of the examples so I simply call: However after the reset it...
Hi,
I have my device based on the nRF52840, we have manufactured some equipments and we have created our own application to manage connection. Everything is working fine...
