Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
Since yesterday's update of the nRF connect extension the device name of the target in the "connected" devices screen is updated from nrf9160_xxAA to nrf9160_xxAA_REV2...
Hi Everyone,
I tried to build lpUart example from samples available. I was trying to debug then I got the breakpoint on
"__ASSERT (lpuart, "Failed to get the device...
i was working on nRF52840 and nRF9160 with NCS v1.8.0.
i'd like to find an API to reboot system. so i tried to call NVIC_SystemReset(). it works in my nRF9160 project. ...
I am currently designing a PCB which incorporates the nRF9160, and I would like to know the devices behaviour in between 2.0 V and 3.0 V, as this is below the minimum VDD...
Dear,
We are working on our custom boards to develop a watch product which need external flash memory connected by QSPI interface. In this product, the UI images and font...
As I learnt, nRF5232 defaut with LDO mode, DC/DC is diabled, but I can not find any config in nRF5 SDK for nRF52 DK,
someone said to use: sd_power_dcdc_mode_set,other said...
Hi,
I've been reading that the nrf9160 can only receive up to ~2KB of data at a time. It seems that the connection terminates if I send too much to the nrf9160. I tried...
Hi again Nordic, I need some pointers. Håkon, a very patient man here, sent me an example code repo of usage of external flash memory on the nRF9160DK. I've tried the sample...
I am trying to bring in the spi_nor driver into our project and was getting errors reading back the jedec id on initialisation so I tried to run the nrf/samples/nrf9160/http_update...
Hello, I have a problem when I enable Bluetooth on my application. If I enable Bluetooth, I can't control gpio pin on Trace DATA. If I disable Bluetooth, I can. It's a hardware...
Hi,
nRFConnect SDK Sample not working (periodic_adv _sync)
I have two nRF52840 DK with nRFConnect SDK 1.7.1
Compiled and run on nRF52840 boards:
\ncs1.7.1 \zephyr...
Hi There
Is it possible to connect to nRF Cloud using a normal 4G/LTE Sim? I see the specs of the NRF9160 show that it supports full LTE and all the Bx bands.
If the answer...
hi,
I am beginner and I am converting an Arduino library to Nordic library, but I have this part code
what is mean begin, I am confused on this part , for example , TwoWire...
Hi,
I have been programming and testing ESB on the nRF52 DK using the Arduino IDE with the sandeepmistry code base, as it allows me to view serial output to a log screen...
