after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am a new beginner when it comes to Thread and Matter. I am trying to run Matter on nrf52840. I flashed the door lock example, commissioned the device using BLE and...
I am using SEGGER Embedded Studio and an nRF52-SDK circuit board to run example ble_central\ble_app_hrs_c from nRF5_SDK_17.0.2. I have a peripheral that reports motions. The...
Hello Nordic, We are preparing for mass production with nRF9160. We have a script to flash, register the thing on AWS and write credentials on the modem using nrfjprog. We...
Using the debugger in SEGGER Embedded Studio and two nRF52-SDK circuit boards, I am stepping through code from the nRF5_SDK_17.0.2 examples.
Very often I end up in file...
Hello everybody,
I'm working on a Project with nrf52dk(nrf52832), and sdk 15.0.0 where I need to read the data from multiple sensors with twi/i2c and send the data via ble...
Hi,
is there a possibility to check in waht CE-level (ECL0- ECL2) the modem is operating on? I know that the ECL is decided by the network and not the UE. However it must...
Hi, I have a problem with simultaneously working Bluetooth LE with LTE. I've use nRF52832 as a Bluetooth controller with is connected to nRF9160 via Low Power UART HCI. When...
Hello I have a few issues which i can't handle. Platform: Visual Studio Code on Windows 10 Board: nrf52840 dk
In my project i need to create workspace which few different...
Dear N ordic S upport Team,
After I updated the nRF Connect SDK (1.5.1 to 1.6.1) and the Modem firmware (1.2.3 to 1.3.0) on my nrf9160 DK device (v1.0.0, SiP revision 2...
I want to use the nRF52840 in the High voltage mode. In this mode as per my understanding, both regulator stages needs to be used. As per the datasheet, configurations given...
Hi all,
I want to update my application with the newer NCS 1.7.0 version. I've changed my west.yml, which containing only NCS-SDK as the only dependency. After running...
Hi,
I would like to setup vscode to develop nrf applications. However, I'm having a problem for the installation of the nRF connect SDK in ubuntu 21.04 (Hirsute Hippo)....
