Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
We bought smart watch from company xyz. Watch is running using Nrf52840 and supports buttonless DFU. we are customizing the smart watch firmware as per our requirements...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. I want to connect with two smartphones. At that time, I want to connect under the following...
Hi, Could you provide source code of nRF Sniffer for Bluetooth LE firmware?
https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE...
Hey Guys :) have a MQTT code that publishes certain AT commands, It works for all cases except Mutlicell 'NCELLMEAS' command. Any help would be appreciated.
[This Works...
Hello
I am using sdk17 and st7735(GFX) drivers.
I am simply printing the sensor value on the display. Initially, it works well, but after a few minutes, the screen is...
Hi,
I am trying to add a temperature sensor to the sensors I can query on the sensor server example.
I have updated a few things
The present ambient temperature...
Hello All,
I am working with BMD300 eval kit and trying to achieve one functionality with UICR CUSTOMER[20] register.
I am fcaing an issue where, UICR CUSTOMER[20] register...
How do I store updated images for both MCUboot and the main App in external flash on the nRF5340 such that the existing MCUboot will apply the updates to the internal flash...
I have nrf52833 DK and i try flash zephyr project to the device but jlink didn't mount or appear in Windows Device Manger. how ever when I press to (BOOT/RESET) button and...
Hello everyone,
for a low-power application, I need to evaluate the total power consumption of the nRF52840 Dev Kit. To verify my measurements, I set one of the GPIOs to...
Hi all together,
nrf52810 SD112 SDK 15.3.0
I have a problem writing to flash with the nrf_fstorage module. I try to write an array of 32 Bytes into flash, triggered by...
We currently want to use the USB Dongle nRF52840 to monitor a communication between two Bluetooth devicesand we are new to this field. First we installed the nRF Connect for...
I am trying to build the AES crypto example in the SDK <install_dir>\nrf5sdk\v16\nRF5SDK160098a08e2\examples\crypto\nrf_crypto\aes\aes_all_cli (nrf_crypto_aes.eww).
Compilation...
Hello,
I am using nRF5340DK board and I am trying to enable high-speed SPI pins in nrf5340dk_nrf5340_cpuapp.dts
&spi4 { compatible = "nordic,nrf-spim"; status = "okay...
