Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hey all,
I have a USB CDC ACM application that works great when it starts, but I'm not able to get it running without the debugger. This is SDK 17.0.2, there is a SoftDevice...
Hi,
I'm trying to use timers 1, 2 and 3 in my application which also uses the app_timer. It works fine when I'm just use 1 & 2 but after inserting the following code to...
Hi, can you point me to the documentation that tells me what preprocessor defines are required for properly building ble_blinky_c or similar please.
The reason is for setting...
Hello,
I am facing problems when I send 3 consecutive chunks of 244 bytes on BLE. My actual task is like receive from SPI and send it to BLE. I am receiving data in chunk...
Hi,
I need to store the 1kB of data in the flash storage and it need to be read anytime and change the data anywhere.
I am using nrf52840 DK and also nrf5340 DK to perform...
Hi Nordic Leaders,
Regarding nRF5340 and nRF connect SDK
Objective: Update blue tooth data transfer rate between 1Mbps and 2 Mbps.
Details:
As it is not possible to...
Hi I am merging BLE Peripheral code and I have added all .c files and added the path in C/C++ compiler and Assembler but it still shows definition missing
You can see...
we are using NRF52832 for my development. Also implemented 1 custom service. Currently we are using 2 standard services and 1 custom service(12 custom characteristics) with...
Hello, I saw another post with a similar question regarding the same error message from a few years ago that went unanswered, I figured I'd reask the question.
I am attempting...
Dear Support
I think gpio_nrfx_port_toggle_bits() is not task / interrupt save.
When between nrf_gpio_port_out_read() and nrf_gpio_port_out_write() a task switch or...
Hey,
I am working on a project as a internee using acconeer xm122 sensor and nrf9160 dk.
I want to know that how I can connect nrf52840 on acconeer xm122 sensor with nrf9160...
Hello,
I am having some trouble migrating from the nrf52 DK to my custom board with an nRF52832 and running as standalone. The application is working as intended when the...
Having an issue that suddenly started with my nRF5340. Tried swapping out batteries, USB power supplies, cables, still have the following error. What is weird is I don't get...
I'm following the secure bootloader examples for nRF5 SDK 16.0.0 with my nRF52840 DK, with Segger Embedded Studio on Win 10 x64. Android Phone used is Samsung Galaxy Note...
