Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
This surprised me.
I disable advertising, stop my app timers, and then loop "while (gpio_sample()) { nrf_pwr_mgmt_run(); }"
I have five low-accuracy nrf_gpiote buttons...
Hi everybody,
I am sending notifications from an nRF2832 (GATT Server) to another nRF52832 (GATT Client) and after some time (sometimes 1 minute, sometimes more minutes...
hello Nordic
i am working with nrf52840, SDK 16.0, s140
i use a timer for sampling of 3 adc channels, (4 times * 3 channels = 12 samples)
i put a pin to toggle in...
in my project, I use SPI inerface (4 pin(pin must can been changed)) communicated with a 4G TF card, this card must mount in Zephyr filesystem , in connect SDK\ v1.5.0\zephyr...
Hi,
I would like to ask a question regarding NFC connection.
When Im using my nrf52840 device to connect with a PC using NFC pad - the NFC triggers the nrf device to start...
Hi,
I am trying to program an extrnal nrf52840 it is Minew MS88SF2 , I did exactly as desribed here at least I think I did, but unfortunatly it always programs the internal...
Hi,
I have installed nrf sdk 1.5.1 via toolchain manager.
I have opened a bash via dropdown in your toolchain manager.
From there I have followed your instructions on...
nRF52840 DKs with SDK 17.0.2, SoftDevice 7.2.0
The resources on this are starting to get a little scattered and possibly outdated. My long range use case is non-scannable...
Hi,
I have added Calendar example application on top of nRF5_SDK_17.0.0_9d13099\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay example code and...
HI.
I searched this one, but I could not find clearly answer.
I want to set BLE Security mode 1, level 1.
I know there is Security mode 1,2, level 1~4.
but on code...
The nRF52840 DK is the recommend development kit, it emulates the nRF52811, and can be used as a starting point for development before moving over to a custom board. Please...
Hi team,
Please help to check if nRF52840 is qualified for ZigBee Smart Energy 1.x protocol, according to customer, seems ZigBee 3.0 is not supporting that yet.
Thanks...
Hi!
If I wanted to use the Nordic Mesh SDK to create a Bluetooth Mesh System, would I have the option to make it closed, so only my dedicated application could provision...
I see that in zephyr main line there are 2 examples:
direction_finding_connectionless_tx
direction_finding_connectionless_rx.
And that:
https://github.com/nrfconnect...
Dear Nordic engineers
I encountered a problem while debugging NRF5_SDK 17.0.2.
I added BAS and IBS services to the “ble_app_uart” program, and everything went smoothly...
