Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am attempting our custom hardware based on an nRF52 chip.
nrfjprog returns the following error message:
ERROR: JLinkARM DLL reported an error. Try again....
Dear Sirs,
We are currently considering to put nRF5430 SoC in our next generation gaming device. One possibility to develop the firmware for nRF5340 SoC would be to use...
Hello,
I have just started learning nrf. I have an nrf52832 board and I want to get and set time using app.
I have seen this https://devzone.nordicsemi.com/f/nordic-q...
Hello
I would like to change the "Company ID" in my application so that it is no longer Nordic's (my application is based on the ble_thread_dyn_mtd_coap_cli example). I...
Hello
I'm contacting you because I'm having a problem connecting to devices that use the ble_thread_dyn_mtd_coap_cli example. Actually, I have no problem when I connect...
Hello all,
I am working on nrf52832 and i need to use the nrf_crypto librariy. The example uses nrf_crypto_aes_crypt and nrf_crypto_aes_finalize function. Although they...
As title, I would like to measure an API function execution time. First method is to print the timestamp before and after the API and the second is to use GPIO and measure...
Hi!
We are developing a board with nRF9160 and want to use it on NB-IoT mode.
The development is made in Romania, Cluj-Napoca and here we have no problem with it. Even...
hello sir/madam .
i am going to implement the code to master and slave clock communication , iam connecting the one nrf52 module to the master clock (through wire controller...
Hello,
I guess it is a simple problem, but I am new to the nrf world, so here is my issue:
I want to use this code to switch on a LED by pressing the on board button...
Hello, I am starting a project and I want to know what is the best way to achieve this. I am using nrf52832, I have the DK as well as custom board. I want to receive an image...
Hello Noridc Support Team and All members,
I am new to BLE development.
I am using the nRF52 development kit and the SDK v17.0.2
My intent is to send the sensor data...
I was studying the Wireshark BLE sniffer packet parsed data for a "Find By Type Value Request" and noticed that the Value was not parsed as Little Endian so it was given as...
Dear Mesh Experts, what's the recommended approach to recover lost mesh keys? Imagine, for example, an industrial mesh installation with hundreds of nodes, all provisioned...
I am trying to store my temp sensor readings in an external flash memory( Winbond W25qXX ).
Can you provide me the respective driver for the same?
BTW I have found driver...
