Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I'm trying to use the nRF91 as a Modem for an Arduino. Is there some example on how to use the AT commands of the serial_lte_modem sample to send a HTTP (or at least...
I built an application for the nrf51822 on top of SDK12.3, to which I added the buttonless DFU based on the "experimental_ble_app_buttonless_dfu" example.
As a boot loader...
Hi,
I want to increase the amount of BLE MIDI packages I am sending. Softdevice 132 nrf52832
MIDI data is sent by notifications and updates of the characteristic value...
Hi,
I want to use uart async on the nrf9160, I get the following linking errors at build time:
here is my prj.conf
If it's defined CONFIG_UART_INTERRUPT_DRIVEN...
Hello,
I have a question regarding the nRF5340 microcontroller or similar. Usually, when programming UART, I2C or SPI bare metal, one is using interrupts, register and buffers...
Hi Team,
We are working on project where we are trying to encrypt the advertisement data (non-connectable) using our own defined keys.
currently I have been through the...
Using Segger with PCA10056 as a debugger connected to a pcb with a NRF52840 on it. Been working fine and I tried building open bootloader and programmed it. I see the device...
Hello,
I am a newby to the nRF5340 and Zephyr and I am stuck. I would like to know how to map physical pins to a particular UARTE.
I have read in the user manual OPS_v0...
Hello,
Currently developing a system based around the NRF9160 running Zephyr. My application is threaded and i would like to run the thread_analyzer. I got this working...
Hello,
I want to hide the BLE(RF signals) completely soon after updating the configuration in my application and whenever I need to update the config I should be able to...
Hi, I'm reading an ADC channel connected to large capacitors. I do the read when charging is off so no ripple. The caps are large (super-caps) so hold well enough to show...
Hey. If the device is repeatedly flashed without turning off its power (it does not matter if I program it through SES or nRFgo), it may start to malfunction or slow down...
Hello
I would like to use three PWM to output multiple sounds with one buzzer.
First of all, I am testing using two PWM. There is no problem using only one PWM, but there...
