Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Forgive what may seem like a stupid question, but...
I would like to create a first reference PCB design using an nRF52832 for an IoT project I am working on.
I...
Hello,
For the function to acquire the FDS file system status, I noticed that the struct member variables are held in uint16_t. Some values, such as words_used and freeable_words...
nRF42840DK, SES V4.52c:
Project was copied from 17.0.0 to 17.0.2 and link now fails:
Building 'ble_app_att_mtu_throughput_pca10056_s140' from solution 'ble_app_att_mtu_throughput_pca10056_s140...
I have been trying to find some help or an example of using a capacitive sense button with the csense library(in SAADC mode) but also read the voltage of my battery using...
The Mac version of nRF Connect shows the Device Information Service characteristic Serial Number String as hex, not a string. It shows properly as a string on the iOS version...
Hi,
I'm changing the peripheral device name by sending a command from the host over ble. I can see the changed device name after the host disconnects. Is it possible to...
Given the info here and here ...
1. Does this mean that the nordic example here is wrong, and that line 54 should be time_struct. tm_mon = month - 1; to account for the...
I use SEGGER build mesh V4.1 project light_ctl and light_switch.
I flash light_switch_server_nrf52840_xxAA_s140_7.0.1.hex and light_lc_server_nrf52840_xxAA_s140_7.0.1.hex...
Hello Nordic
I am using nrf52832, skd 16.0 , s132 v7, the data with the new FW will be delivered via UART
I wish to understand some issues regarding FW update, after doing...
Hello,
I am working on SDK v14 version mpu6050 sensor. I found an example of mpu6050 here.
https://github.com/Martinsbl/nrf5-mpu-examples
And here I found a way to...
Hi, I am working on nRF52840. I want to add Device Information Service in ble_app_template. (as shown in the attached image its from another device) How can I add? Kindly...
Hello,
nRF52840, SDk16.0, Softdevice 7.0.1,
I am having the following flash write error message while writing data to flash. I'm using FDS library. Interestingly this...
Hi, I am following the below link for creating custom services/characteristics. https://github.com/bjornspockeli/nRF52-Bluetooth-Course
I have set the device name as...
Hi
based on nus example , I'd like to create RX/TX characteristics with a custom UUID (128bits)
My problem is about the UUID characteristics versus UUID service, for example...
