Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am new to the nRF world of controllers. I am planning to use these wireless MCU for our IoT enabled products. We are in the early stages of finalizing the MCS, so...
Hi,
I'm including additional C libraries into the asset_tracker sample and have already hit the wall exceeding the space allocated to FLASH
Memory region Used Size Region...
I've noted an odd bug in the SAADC specifically with the Low Power Mode enabled. I used the SAADC to either gather data via Timer+PPI during a data collection mode, OR polling...
Hi,
I'm working on audio codec(ES8374) which using I2S to transfer data, and this part is fine.
Since project require low power consumption, All peripheral should be closed...
Hi everyone,
I am facing the weirdest problem here.
I am working on a custom board using the NRF52832 which I was able to program without issues. I have been working...
Hi,
I am trying to test LESC Security Mode 1 Level 4 bonding with a peripheral ble_app_hrs on PCA10040 and pc-nrfconnect-ble (v2.2) with pc-nrfconnect-core(v2.6.2) with...
AoA/AoD functionality is critical to a product I'm developing.
I'm told that this functionality hasn't been released yet.
I'd like to get a rough idea of when hardware...
I am usin the nrf52840 with USB DFU on the nrf52840 dongle. I want to use the DFU since I may be needing the reset button or will not be configuring it. If I don't configure...
HI nordic,
I had a NRF52832 DK which acts as central. In ble_app_uart_c example i need to scan the battery level of nearby beacons without connecting to the beacons
How...
Hi,
We have a nRF52-PCA10040 with the Heart Rate Collector example in the version 15.3.0 of the SDK which has some trouble connecting to our Bluetooth 4.2 notifier.
...
The SDK and SoftDevice documentation show that application is located at lower address than the bootloader.
Is it possible to rearrange memory layout to something like this...
Is there any example code for sending the data to esp8266 from nrf52832 using uart.
I want to send data via nrf connect application to esp8266...
Till now. I am able to...
I'm studying nRF9160 for our new project.
The GPS accuracy of nRF9160 is 5m. I got this spec. from brief specification of nRF9160.
My questions are below:
1. Does...
Hi experts,
I used power profile kit (PPK) board to measure the current consumption of nRF52-DK which containing nRF52832.
When i using PPK and nRF Connect APP for measurement...
