after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
i am trying to run advertising.py from pc-ble-driver-py .
i am keep getting exception from
except IndexError : raise NordicSemiException( 'board not found' ) is there...
I am looking through the BLE examples, but I can't seem to find an example that best fits my project scope where I wish to have a BLE central service that reads data from...
Hello Nordic support team I want to send command from hm10 ble chip to Nrf52832 dk board.So before I start to implement this I want to know that HM10 ble chip can communicate...
Hi, all.
I want data read from gyro sensor through i2c, and then send it through bluetooth equipment.(PC or iPhone and so on)
But i don'k know how to send gyro sensor...
I am asking about using the sd_rand_application_vector_get function; it seems that it causes my board to crash, and it never returns a success code.
I have already seen...
Hello:
I am upgrading my application to use Mesh SDK 3.0.0 (I was at 2.1.1). In my application, I process the mesh from the main loop (per the instruction in the Interrupt...
Hello All, I would like to implement tracking over MESH network using nRF52840. 1. In my MESH network, there are some devices who continuously advertising (say beacon). 2...
HI.
I am following the document http://infocenter.nordicsemi.com/pdf/nRFConnect_BLE_User_Guide_v2.2.pdf to work with nRFConnect desktop App and my DK BMD300(Rigado). ...
Hello,
I'm trying to play voice using PWM in nRF51822.
I've already experienced this using other MCU before.
So. I'm trying.
Voice source data is 8bit / 8K / mono...
Hi,
I am working on nrf52832 , SDK15 and softdevice S132. I am modifying the ble_app_hrs example code in SDK
I was trying to implement a whitelist with the address of...
I am using ble_app_uart SDK_11 s130 on nRF51-dk. I would like to make the device running on ble_app_uart connectable but not discoverable. The Android app will have pre-knowledge...
I am using nRF52840 with sdk 15.0 version. I am able to read OR write data into flash using fds library. But now i want to write one or two bytes into flash and read this...
Development Kit - nrf52
SDK Version - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Setup : I am trying to interface an E Paper Display...
