Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm modelling a complex system with multiple BT devices based on the NRF52 using a very detailed model of the RF.
The system is based on the NRF52 using the mesh stack to...
Hi everybody!
My goal now is to use nRF52832 as a intermediary for an update package. In other words, my goal is to send a file (probably .zip package) to a board and save...
Hi,
When running the unit tests for Mesh SDK 3.1.0 I get the following failures.
83/92 Test #83: generic_dtt_client ...............***Failed 0.00 sec
From the log I...
Dear DevZone,
I'm new to the nRF52-DK and Nordic in general. I'm trying to set up an nRF52-DK to use with nRF Sniffer, and not having any success.
I have tried following...
Hello!
I want to ask about read operation on nrf51822.
In your examples, as I understand, BT stack handles Read Request automatically and then sends Read Response. The value...
Hello,
I am beginner for bluetooth technology and have very interesting to this technology
I have developed new board (4 pcs) for nrf 52832 and soldered all parts from...
Hello.
Please teach me how to turn on DEBUG flag on Segger Embeddid Studio.
Environment: SDK 15.2.0 and SEGGER Embedded Studio Release 4.10a Build 2018110203.37618 Linux...
Hi I'm facing problem while programming my custom nrf52832 board (It might be issue with flash/ROM setting) its saying this hex file has a data in softdevice region . I'm...
Is nrF52840 VDDH pin only used for REG0 LDO/DCDC regulator output to generate VDD power for the GPIO circuitry?
or is VDDH power used to power some other internal circuits...
Is there a way to access the Gazell heartbeat timer? Ideally I would have a callback to my application when the heartbeat occurs. The main motivation for this would be to...
Hi,
What I did:
Already connected the custom board with nrf52832 chip on pc with python
Already receiving data from the board
I want to have the python code that...
The GPS antenna just fell off the board. Seems like the part has a cold solder joint. This led me thinking that the LTE antenna might also have the same problem. I had no...
I choose one NRF52 DK(nrf52840_pca10056) for my daily development. After hundreds of erase and write cycles, the DK won't behaves like it should do. The other DKs runs well...
