Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Currently we're experiencing some problems to detect events from npm1300 in our custom board but the same issue happens with nrf54l15dk plus npm1300-ek boards when running...
Hi,
We're using the nRF54L15 driven by a 5ppm TCXO connected to the LFCLK. Our application measures the timing external pin events; the accuracy of this measurement is critical...
Hi
I'm having trouble finding two documents: the 'nRF91xx Kits Reduced Receiver Sensitivity Issue.PDF and the related design files for the extra filtering on the nRF91....
Hi everyone,
I believe the object_type should not be of type uint32_t, but of type uint8_t (or maybe nrf_dfu_obj_type_t).
This is the structure I'm talking about inside...
We have been trying to upgrade nRF connect SDK from v3.1.1 to v3.2.1 and run into the following issue: When we enable CONFIG_PM_DEVICE_RUNTIME=y after flashing, the device...
We've encountered an issue when reading OTP memory using tfm_platform_mem_read() .
After invoking tfm_platform_mem_read() , any subsequent call to k_sleep() (or any other...
Looking at this forum post from 11 months ago, and I'm confused about the guidance given. https://devzone.nordicsemi.com/f/nordic-q-a/99083/reading-uicr-value-at-runtime-for...
Hi,
In ncs/v3.1.0/ modules/hal/nordic/nrfx/drivers/include/nrfx_nfct.h, the enum ' nrfx_nfct_param_id_t' is defined as:
In the nrfx support libraries shipped to us with...
We have a board designed with nrf54l15 and we plan to use the RRAM to store the image. That is, no external flash to store images.
For this design, is it possible to use...
Hello,
I am trying to get to grips with the nrfx driver: GRTC.
I want to create the following sequence with the lowest possible power consumption. Activate output 1 for...
Hi
I have two nRF5340 DK boards.
I cannot remember what I last used them for, but I can no longer connect up to them.
In VSCode, when I usually connect to an nRF board...
Hi, I am able to flash my XIAO nrf52840 using my nrf52840dk however the code does not run once flashed. I checked and the code itself is starting at 0x00027000 presumably...
With NCS 3.2.1 I can't make use of custom mbed TLS config headers anymore, the MBEDTLS_CFG_FILE KConfig option always get overwritten. Previously setting CONFIG_CUSTOM_MBEDTLS_CFG_FILE...
Hi,
I tried searching public question on the matter and wasn't able to find anything reminiscent of the problem I have.
I'm developing a presence sensor using ZigBee protocol...
I'm working on formalizing our DFU process. We're building on Zephyr and using mcuboot as the bootloader. We're using ble to transfer the images over smp and then our current...
