Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi I tried to put descriptor on the characteristic recently and it didn't seem to work. Is there something wrong with that?
If I take the following code that adds...
Hi, I have a brand new nrf5340dk and the debug interface is not showing up when connected: I have other nrf5340s that work so I'm sure its the board specific.
Board label...
Hello,
Customer would like to know if part below:
NRF52840-DONGLE
Customer would like to know if there is any connector that Customer is able to use to the above part...
Hello,
I am relatively new to the nrf9161, but I am running into an error with my build.
'TFM_PERIPHERAL_DPPI_CHANNEL_MASK_SECURE' undeclared (first use in this function...
Hi there,
I intend to use pynrfjprog in development replacing another, older library. However, any call to the API which involves the nrfjprog DLL returns:
This is on...
Hi:
MCU: nRF52832
The device is powered by a battery. When the battery voltage drops to around 1.3V but is not completely depleted, if the device is charged at this time...
I am in the development phase of a Bluetooth based system design, which will be able to receive audio stream from any mobile device and play on the speaker, and also it would...
Hi,
I'd like to provision my Thingy91x for use with my nRF Cloud (so I can use location services). How do I provision the Thingy91x for use with my own nRF Cloud? What should...
Hi.
I read on the download site of the nrf command line tools that they are being deprecated.
I want to be sure that i'm correct here: 1. nrfjprog is replaced by nrfutil...
I have an application that runs on nrf9160 and uses nrf52811 for Bluetooth with client-host setup. Problem is it sometimes crashes on startup going into endless reboot loop...
Hi, I recently purchased an nRF52833DK and tested the attached code. When using Gazell, the maximum throughput I achieved was around 85,333 bps. However, according to the...
How to reproduce the issue:
We have used the standard hello_world sample application in the zephyr repository. CONFIG_I2C, CONFIG_SHELL and CONFIG_I2C_SHELL configurations...
Hi, I run this sample https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/mesh/dfu/distributor on two NRF52840DK, but I cpouldn't do the update, here is the...
