I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi
I am using nrf Connect sdk 2.9.0 Visual Code IDE.I have added the following configuration in the prg.conf file:
But still I am not asble to receive more than 20 bytes...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader.
I had a mucboot setup that fitted...
I have a modified asset_tracker_v2 running with SDK 2.5.0. It is connecting to AWS and sending data perfectly. It has been running for several years without a problem. I am...
Hello,
I’m running the AWS IoT sample on nRF9160DK v1.1.3 using nrf-sdk and toolchain v2.9.0, modem v1.3.7.
Everything works fine when following the instructions with...
Hello community, I am currently looking for a solution outside the 2.4 GHz band and I came across NR+. Does it suit my needs for M2M (Machine to Machine) communication? If...
Dear Nordic experts,
My question is simple, how to get the 6 octets default MAC address by app SW in nRF52840. The question was already raised by someone some years ago...
I have an issue when trying to install nRF Connect SDK on my work computer. I have installed VScode, the toolchain and the nRF Connect extension. The next step would be to...
I have been trying without success to install either the v2.7.0 or v2.8.0 SDK onto my Windows 10 System. Every time/method I've used results in an error equivalent to
...
Hi,
SDK17, Softdevice S112, NRF52805 custom board.
I have baremetal bsp implemented but I am new to Softdevice and struggling a bit with an interface concept beween two...
Hey,
I'm using the nRF5340 and want to run the PTS test with the following configuration: The CAP initiator establishes two audio streams within a single connection to the...
Hello,
We are currently experiencing some unusual behaviour on our feather board (circuit dojo, nRF9160 chip) which we are seeking advice on.
Whats happening:
Device...
