Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I was able to set up 2 thingy91's using the nRF9160DK to update the firmware and the asset tracker is working on the 2 thingy91's. I've tried to provision the DK and I get...
Hi,
I am trying to port the nRF5_SDK_17.0.2_d674dde\examples\nfc\writable_ndef_msg and my linker cant find the definition for the following symbols-
linking... .\_build...
Good afternoon ladies and gentlemen,
Just a really quick question/observation... am I going bonkers? or is the link to Segger Embedded Studio on this Nordic Page incorrect...
Hi nordic:
I use nrf9160 to test the new driver mainly due to the following two problems:
Environment: sdk 1.8.0-rc2 modem: nrf9160_1.3.1 lwm2m CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hi There,
I have a question now. If I want to alter the frame format in the data linker, how do I do?
I try to find the source code of the data linker layer in the Mesh...
Dear Members, I want to log my ANT+ HRM into SDcard, I tried with flag, but it never goes to main loop, I'm using nRF52840 Code ANT HRM interrupt :
on the main loop...
hello,
i am using nrf52832 with our customized board and i am trying to send 427 characters string at a time using lbs service but it only accepts 200 characters in single...
Hi! I've got over 2000 smartwatches out in the field that are using the nRF52840. The hardware designers thought it was a great idea to expose the SWD pins along with the...
Hi experienced people
I try to initialize twi on pin 44 and 45.
ret_code_t err_code; const nrf_drv_twi_config_t twi_config_top = { .scl = 45, .sda = 44, .frequency = NRF_DRV_TWI_FREQ_100K...
Is there an easy way to get the manufacturing data from an advertisement packet in the 17.1.0 SDK?
I also struggled with extracting the rssi value and ended up using:
...
I'm using nrfx_saadc V2 in nRF5 SDK 17.0.2. In nrfx_saadc_abort nrf_saadc_task_trigger(NRF_SAADC_TASK_STOP); is called regardless of if the ADC is currently running. If the...
Hi!
We're using the nRF52810 chip, so we have a very limited amount of flash memory. We're looking at every opportunity to save some space. We currently run with a modified...
I've got the USB CDC ACM example up and running. I'd like to do something similar on the nrf52840 Dongle but rather than using a UART for the CLI, I'd like to use a second...
hi support team,
customer has one question about USB device to restart manually, because customer need to change the HID descriptor for some reason.
i tried on usb uninit...
