Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Most times the Online Power Profiler doesn't even load the graphics, etc. 80% of the time it doesn't finish loading and I have to reload multiple times. I have a 1 Gigabit...
Hello,
I'm using nRF52833 for my application. Unfortunately, my dev kit can not connect to my PC when I use cable to connect it to my PC. It can supply voltage for my kit...
Hi to all, I have found that using SDK17.0.0 on NRF52832, whenever I try to use NRF_LOG_HEXDUMP_DEBUG for a large buffer (more than a 1000 elements), I get a Data Access Violation...
Hello,
I am using NRF52840 DK to toggle led 3 and 4 back and forth (when LED 3 is ON, LED 4 should be OFF and so on). I have to toggle them in a small time interval of...
I get disconnected when receiving notification from characterisitc.
Everything looks fine in nRF Connect app - screenshot below:
Strange behavior begins when I am trying...
hi,
I try to realize all parameter functions in the peer manager. ( I use SDK 15.2.0 )
I expect to design is bond total max 4 in the product. I have some question in below...
Hello,
I'm working on NRF9160-DK. I would like to be able to put the card to sleep in the deepest sleep possible to be able to save as much energy as possible and to wake...
Hi to community again!
I'm having trouble with TWIS during page erase on nRF52840 (FICR "Read 4 bytes @ address 0x10000104 (Data = 0x41414330)") as the bus is stalled...
Hi,
I'm using SDK 17.0.2 on NRF52832
I'm getting an error "undefined reference to `__RAM1_segment_end__'" in "Output/<name>_Debug/Obj/ses_startup_nrf_common.o: in function...
Hi Lorenzo,
I have gone through most of the documentation related to Immutable (SB or b0), McuBoot and application and i have the following queries:
which one should...
Hi,
1) i try to build the eddystone sample program and it prompt "....missing micro-file......".
2) i went support site and search thru some recommendation.
3) After...
Hi all,
Download and build SDK excample in MDK, fail!
Error #543: Device nRF52840_xxAA(Nordic Semiconductor) not found, pack 'NordicSemiconductor.nRF_DeviceFamilyPack_NordicLicense...
