after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I compiled 4.0.0 in the past and the generated libraries were named "pc_ble_driver_shared_sd_api_vX.dll".
Now I compiled 4.1.1 and the libraries are named "nrf-ble-driver...
Dear Nordic:
My nRF82832 codes based on nRF5_SDK_15.2.0_9412b96 and used s132_nrf52_6.1.0. But I find the Bluetooth signal of nRF82832 can’t be scanned by smart phone which...
Dears,
I am using DK PCA10028 (V1.2.2). Start developing from SDK_12.3.0\examples\ble_peripheral\experimental_ble_app_blinky.
All system configuration keep the same (ADC...
Hi,
I'm using:
nRF52840 Preview DK
Zigbee v2 (nRF5_SDK_for_Thread_and_Zigbee_2)
Segger Embedded Studio for ARM 3.52
Developing on a MacBook (macOS Mojave v10.14...
2017-04-12T06_05_42.374Z-log.txt
Hello,
the example "experimental ble app cgms" (SDK v13.0.0) failed to pair with nRF v1.1.1.
The error code was Authentication failed...
Hi, guys. I'm using two PCA10040 boards. One is using the ble_app_uart__saadc_timer_driven__scan_mode example
github.com/.../main.c
and the other board is flashed with...
Hi,
So I've been trying to get the SIP down to use its most minimal power consumption level to the claimed floor of 7uA or so (I'd take 20uA even), and have stripped the...
Hi everyone, I am using nRF52832 (PCA10040) and ICM 20648. I want to write a I2C aka TWI interface to read accelerometer and gyroscope readings and print them out with TeraTerm...
Hello,
Does anyone know if I can use J-link BASE for programming in factory. I haven't seen any limitation related with it why can't use it for production purposes but If...
Hi,
In app design stage, and we cant connect to the bluetooth device UNLESS GPS is actually on. I dont mean permission, that's fine, I mean actually having the gps service...
Hi, I just started to develop a new project with nRF52840 and I've been trying to understand about white listing feature of BLE.
As I need white list to skip unknown device...
Hello everyone,
We are using the nrf52832 Dev Kit ( PCA10040 1.2.1 2017.49 682663245)
SRK Version 15.3
OS : Fedora
On the saadc example in the peripheral folder...
Hello,
I need to convert a standard 32 bit floating point number to IEEE-11073 16-bit FLOAT with 12-bit mantissa and 4-bit exponent (source: https://infocenter.nordicsemi...
Good morning,
I have been asked to merge the code developed by two independent teams. Of course, each one of them took their decision on the management of time, and of course...
