Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hey everyone,
I'm having problems with my app's ram usage as you can see from my previous questions.
I've tried this little piece of code:
void memcheck(void){
...
hello friends,
Im developing an application where im trying to connect a central and a peripheral but since the signal strength depends upon run time environment i am getting...
The App ~ BLE Stack is the device, Central is smartphone.
is correct?
I don't understand this sequence.
Do not adv_data_set and the adv_start before the scan?...
I'm attaching a function where I use the sd function :
void edit_speed_ID(uint8_t speed)
{
uint32_t value;//, err_code;
value=5 * speed;
while(sd_flash_write(address...
Unfortunately it seems my post devzone.nordicsemi.com/.../ has been lost.
This is a re-post.
I am trying to manipulate Flash data in CODE_SPACE one page at a time. Currently...
I'm using nRF51822 for ble.
For my application, I need to increase rf power.
( My application needs +10dBm)
In case of CC2540(TI ble chip), there is application note...
Hello,
I have 2 nRF51822 with S130. One is central, the other is device.
I want to exchange custom data between these 2 devices after connection. What is service best...
Hello,
I do communications between 2 nRF51822 (one central and one device). Once they are connected, cant i do a kind of deep sleep and freeze stack state for 1 minute...
I'm getting a hardfault on some float operations that I wasn't getting before I upgraded to SDK 6.0.0 and SD 7.0.0. At least, I wasn't getting them at all before that and...
Hi:
I use spi0(0x40003000) to wirte data to external flash(W25Q64) with SD8.0(sdk8.0.if I write data without sd, it is OK), and when program run to rx_data[number_of_txd_bytes...
A friend of mine asked me to help with thinking about a solution to create a RF communication between 8 robots and 1 access point. Not a lot of traffic, just to signal that...
Hi everyone,
We are making a BLE peripheral that measures some data and keeps it ready for the mobile phone to connect & poll the data.
The data should be private and...
I am trying to use the template to create my own application. In two places I have read, that to add my own services, I just "Double-click the Serives folder in the Project...
Hello everyone,
I had some troubles some time ago with Softdevice s120, and finally solved it to work with nRF51822 thanks to Aryan .
The problem is that, when I upload...
I'm following the official tutorial for using pstorage and this the simplest test code I've come up with:
static pstorage_handle_t base_handle;
static void test_pstorage_cb_handler...
