Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi, I recently purchased an nRF52833DK and tested the attached code. When using Gazell, the maximum throughput I achieved was around 85,333 bps. However, according to the...
How to reproduce the issue:
We have used the standard hello_world sample application in the zephyr repository. CONFIG_I2C, CONFIG_SHELL and CONFIG_I2C_SHELL configurations...
Hi, I run this sample https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/mesh/dfu/distributor on two NRF52840DK, but I cpouldn't do the update, here is the...
I know that Zephyr supports its own test framework ZTest, but I have used CppUTest extensively on past projects.
I'm also using Quantum Leaps QP (for which there is a Zephyr...
Could I know how to enable openthread log in bulb project?
I have added some logs in modules/lib/openthread, but it can't be displayed in tool, how can I fix it？
BR
...
Hello.
I am trying DFU with reference to DevAcademy Lesson 9 . I am glad to see that it has been updated for v2.7.0 - v2.9.0. I am interested in the following settings....
I am working on nRF54L15 with ncs v2.9.0 and I have migrated the pwm code which was working well with nrf52840 but with nrf54l15 it is not working. I tried to debug the issue...
I am developing AoA for nRF52833.
Please tell me about antenna switching.
Setting:
PSEL.DFEGPIO[0]=28 PSEL.DFEGPIO[1]=29 PSEL.DFEGPIO[2]=30 PSEL.DFEGPIO[3]=31
SWITCHPATTERN...
Hi folks.
recently I've been experimenting with the nrf7002dk Development Kit, and I'd like to move forward with prototyping a custom board around the nRF7002 + nRF5340...
Hello,
I'm trying to work through exercise 2 of the Nordic Developer Academy. It has me using the Blinky Sample. When I add a build configuration I get an error. I have...
The board is nrf52840 based using mcuboot via usb, mcuboot can be activated using a switch, and is indicated via a led, all setup via device-tree, so no legacy here. Software...
Hi,
I am trying to connect nrf9160 to CMW500 callbox however I am not able to connect to it. Switching to a commercial sim card I was able to connect to the network. I am...
We are finding an issue where after a network is running for a while we are unable to interact with devices beyond connecting to them via the nRF Mesh App. Specifically, we...
HI,
I found that nrf Desktop (v2.9.0 nrf54L15) surport fwupd support, it's same with old mcuboot DFU? and i want to upgrade from SPI, how can i do? is there any demo code...
