Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello, I want to write an applicatin that gets at_coammnds from the terminal via uart, sends the command to the modem and then sends the respond back via uart. I have two...
Please provide an example of using app_sched_event_put() to pass a string.
This is what I have at present:
The handler appears to get the first 4 characters OK (perhaps...
Hello,
We have a sensor with 2 ADCs inputs meauring identical LMT70s on the board. With one of our older firmwares we get the accurate valudes of 22deg or so on both channels...
I am trying to install the toolchaing under Ubuntu 24.04LTS.
Installing via the toolchain manager does not work. I get the following error.
Failed to clone the repositories...
Hi,
The version of the nrf connect mobile app is not 4.29.xx but 4.26.xx.
The dfu generally succeed on our target however sometimes it failed on another target device...
We use nrf52833 chip but I don't know which SDK and version.
but I used "s113_nrf52_7.2.0_softdevice.hex" in our project having started on 2021.01.27.
So, It's old project...
We tried to see device logs from our target.
We use dfu bootloader for our custom target.
I enable RTT logging on our custom source for our target.
Then we can see...
Hello everyone.
I am developing a custom board using the nRF9160. I tried using the RAM power-down library based on the Power optimization recommendations page of the nRF...
If anyone has successfully stored and retrieved settings on the nRF52840 dongle using any method, please share your approach.
I'm trying to store and retrieve settings...
1. Description and how to recreate it
Im attempting to flash a custom board with a nrf5340 on board using mcuboot via nrf Programmer v4.5.0.
When I put the board in bootloader...
Hello.
Since nRF Connect SDK v3.0.0 has been released, I am testing the sample program . It is a sample I have frequently used from previous versions. The provisioning with...
hi support team,
DTM is not able to build thingy53, do we have any support for this board? or any instructions for it?
radio_test is also not able to build thing53.
...
Hi everybody.
I'm developing my own board based on nRF52840 SoC. I'm using nRF Connect SDK 2.6.1. I need to log the environment events by date & time details on QSPI using...
I am trying to add Coded Phy to my Zephyr BLE Mesh project. I know this is not officially supported, however is possible. Running the stock BLE Mesh Zephyr sample, I keep...
