Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello everyone,
I remember doing a project with PCA10028 board and S110 SDK a year or a year and a half ago. Now i want to do another project but all my materials which...
Hello,
I am writing this question in reference to this question . I was asked to be more specific about my question by my colegues. I do understand that this is a duplicate...
Hi,
I checked the flash_fds example. I could not tell the address it tries to access to. Is there any way I can find the address? Can I limited it to a certain address range...
According to this article, https://www.nordicsemi.com/eng/Products/Bluetooth-5, it appears that the nRF52 should be able to support standard BLE at 2Mb. However when I look...
Hi Nordic
I am using sdk 14.2.0 version and s332 soft device. Now I have completed the bicycle speed cadence code that works with ble_ant. It worked well as I wanted. But...
hi,
I am a fresher .I am asked to do the communication between nrf51 D K and moblie phone( nrf connect app). Can anyone provide me a sample code and required documents to...
Hi
I am using SPI to talk to an LIS2DH with an NRF51822. I have merged the SPI Master example with the ble_app_rscs example and as soon as the ble advertising begins, my...
nRF Connect has no serial ports to connect to. I've looked in /dev. No unusual tty or cu devices listed. I've checked the forums. Mentions is made about Segger link and "...
Board: custom board
Mesh SDK: V1.0.0
Softdevice: S132
IDE: SEGGER Embedded
BLE: nrf52832
When I test the steps specified by “Interactive PyACI”, I can control client...
Hi,
I have spent a couple of days trying to find formal documentation on how to update the nrf SDK. I am currently on 11 (as keil pack installer states the version of...
Hello everyone, I come from the 8bits MCU world and I'm used to program my chip with a debugger like Atmel-ICE. But with 32bits MCU I'm a bit troubled to program nRF82832...
I'm using the IoT bootloader from NRF52 SDK 14.2. When the bootloader has nothing to do and starts the main application, the FDS calls all fail in the main application. When...
We're using QuantumLeaps and want to send a message each time a character is received on the UART command line interface transport layer.
Where in the SDK source code would...
