Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have build the below sample for a nRF52dk-nRF52832 board.
v1.8.0\zephyr\samples\drivers\spi_fujitsu_fram
At compile time I've got this error:
I have followed...
According to Zephyr documentation it is possible to define a thread with K_FOREVER delay so it will not start till k_thread_start is called
https://developer.nordicsemi...
Hi,
i am using a PWM signal to control the brightness of a LED. When the brightness is at zero, i have a random flickering on the LED.
This signal is also present at the...
Hello, i'm using the example ble app uart and I would like to know the maximum data that I cand send to my putty and my phone. Could I have to procedure? I would like to send...
Hi,
I trouble the support team for quite a few months now with NRF5 and I am now trying to get started with the up to date SDK and hopefully being able to get along with...
I have an application using the nRF9160 and its LTE modem to connect to a LWM2M server. During some debugging I enabled LWM2M_LOG_LEVEL_DBG and saw that I consistently got...
Hi,
I recently designed a prototyping board featuring the nRF9160, which we got made for a couple of reasons.
To have multiple boards to test with
Potential to have...
hello
i want to send the data from my 5 of nRF52840DK to 1 of raspberry pi4 , i known the nRF52840dk has built-in bluetooth ble5 and raspberry pi 4 also integrate bluetooth...
I am noticing that particularly with the transmission of bytes over UART while scheduler is running, either some bytes go missing or the entire set of bytes aren't sent or...
Hello
Question: On what clock/clock-speed does the system tick timer run, when configured to use the external clock instead of the CPU clock?
I've seen a couple of...
Good afternoon,
I noticed in the nrfx driver folders there are two differente implementations for ADC: "nrfx_adc.c" and "nrfx_saadc.c"
What is the difference? Why two...
I had successfully interfaced lis3dh on nrf52 dev board using i2c protocol, i am getting raw values of x, y and z but i don't know how to interpret those values i.e. convert...
Hi,
Is there any similar to Online Power Profiler for Zigbee? How much my nRF52840 application should consume when using zboss stack? What is the minimum expected consumption...
Hi all,
I'am doing DFU via OTA
The device will be in bootloader mode ?
my current application has a thread running when i'am initiating DFU via OTA in nrf_connect app...
