Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi, I want to build a Bluetooth LE peripheral application with nRF5340. The channel must be able to sustain an output stream of 8 kbit/s.
Other desirable features are: ...
GPS sample stops updating timestamp after a few days of uptime indoors
Tested devices: Thingy:91, nRF9160dk Tested firmwares: mfw_nrf9160_1.2.1, mfw_nrf9160_1.2.2
Demo...
I have a nRF52820-DK evaluation board which I am trying to develop on. I followed the manual install procedure on to my xubuntu Linux desktop. I followed these instructions...
Hi ! I have configured Zero bit length of S1 in radio packet ( nrf52840 ) but it is still mapped to the RAM.
... ((NRF_S1LEN_BITS << RADIO_PCNF0_S1LEN_Pos) & (RADIO_PCNF0_S1LEN_Msk...
We would like to use Zigbeee on the nRF52820, however, it seems from other threads that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it,...
Hello sir,
I am using nrf52832 soc with customized board having gpio pin with P0.2,P0.3 and P0.4 used for led blinking for different purposes.The function used for led blinking...
Hello,
I have a problem with the SPI of the nRF52DK 52832, and Zephyr 1.6.1. I have to transmit 10 frames of 5760 bytes each to the TFT display with the ST7789 driver. ...
I am just creating this issue as a bug report. (my github issue: https://github.com/zephyrproject-rtos/zephyr/issues/38688 )
There is currently a bug in zephyrs handling...
Hi!
I had some time with the Thingy:91 and was able to get my own application running on the device using the nRF Connect Programmer application. To eliminate the need for...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to read / write a value to the specified address of the flash. According to...
Hello.
I'm trying to get data from a pressure sensor.
But it seems that BLE device is not properly got data from the sensor.
Here is a data sheet of the sensor. (Please...
Hello everyone, I am using NrfConnect with Zephyr on Segger embedded studio . I want tu use the math logarithm function in my code and print the result on the debug terminal...
Hello,
We have a wearable-type device with custom BLE services and characteristics. We would like to log all data from our services on a PC. Would you happen to know of...
Hello!
Can anyone explain, why APP_USBD_CDC_REQ_SET_CONTROL_LINE_STATE event in app_usb_cdc_acm library fires for DTR signal changes only, but not for RTS signal? I try...
