I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
I'm using NCS 3.2.4. When USE_PARTITION_MANAGER is active, the ARM linker script defines ROM_SIZE as PM_SIZE (the full app partition) without subtracting CONFIG_ROM_END_OFFSET...
I have a simple code. send msg to a message queue. and handle the message in another thread. I my old environment ncs2.4.0. I looks works well. // after get msg queue. to...
Dear Nordic Engineer,
Hello!I am planning to develop a 2.4G, BLE and USB mouse. Both the dongle and the mouse device will use the NRF52840. I want to use BLE and ESB simultaneously...
Hello,
For my prject I need to tiggrer a timer start using a pin. I'm trying do do it using PPI but it seems that GPOITE can only create events on input pins. If anyone...
The MCU is NRF54L10, the SDK is NCS2.9.1, and the firmware is updated using MCUboot update mode.
Configuration as follows：
# sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I write this information for the sake of completeness. I don´t need Zigbee2MQTT support from you. Instead, support with the Zigbee firmware is required.
I´m working...
Hello,
I am currently testing a setup combining the nRF5340DK and nRF7002EK using NCS/Toolchain v3.0.0 .
I need to reassign the 8 GPIO pins (including Bucken, Grant, etc...
Background:
Platform : nRF52832 with nRF Connect SDK (NCS) v3.1.0
BLE Roles : The device operates simultaneously as:
A BLE Central (NUS Client) , connecting to an...
While installing the nrf connect extension for VS code and installing the SDK and toolchain I have encountered the same issue multiple times. The toolchain and SDK got installed...
Hardware: nRF5340 DK
nRF Connect SDK: v2.6.1
Description:
I am working on a project where there is a need to transfer a large amount of data from NET to APP core. We...
Hello,
I am working with nRF9160 already since SDK v2.1.2 and with every update there are some functions not working anymore, although not mentioned anywhere in the documentation...
I am currently working on a FOTA implementation I am using nRF9160 DK with nRF Connect SDK v3.1.1 and the LwM2M client sample (/samples/cellular/lwm2m_client/). I am using...
Hello All, I hope everyone is doing great. I am an embedded enthusiast and i recently started working on nRF boards. I am currently facing error while setting up my custom...
Hello, I would like to know if the nrf9160 flash can be loaded locally and not via wireless. We have a lot of devices with data to preload and is unviable to download the...
Simple sQSPI test app locks up on LM20
We've got a simple display driver working for the nRF54L15. We used the mspi_sqspi driver for reference. As far as I can tell, there...
