If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi, I started my project with SDK version 2.6.1 (starting from the 'hello_world' example). I added mcuboot (CONFIG_BOOTLOADER_MCUBOOT=y). I followed the instructions in the...
Use nrf_modem_lib_init() to initialize the modem, followed by lte_lc_connect() to connect to LTE. However, it consistently fails to connect to LTE. After it times out, the...
HW: 52840DK PCA10056 3.0.1 2023.16
NCS SDK: v2.8.0
I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
Hello.
I am trying to use nRF Connect SDK v2.8.0 and nRF52840 to run Matter's Light Switch and Light Bulb.
I was able to confirm that it works with nRF52840-DK, but...
Hi there,
Our firmware is built on NCS 2.6.1 (soon to be ported to 2.7.0) and uses MCUboot.
I want to set REGOUT0 to 5 (which corresponds to 3.3V) and the `nrfjprog -...
I am trying to upgrade my project which is previously build with NRF connect SDK 2.6.1 to 2.8.0
I am getting this error while building
warning: NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Greetings,
when trying to compile simple GPIO configuration for NRF5340, the compile fails with:
In file included from C:/Apps/NordicSemiconductor/SDKs/v2.7.0/zephyr/include...
Hi
I have set up VS Code (1.93.1) on my Mac (mac OS 14.6.1) with nRF packages and zephyr installed. My nRF5340 DK is also found (however, instead of a nice identificaiton...
I am reaching out to inquire about the support for the indication method in the Nordic nRF52840. Could you please confirm whether this method is supported in the Nordic SDK...
There was no problem when the current version of ccache was 4.6.1. However, the current version of ccache, 4.10.2, behaves differently with the --specs option. It will do...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
What we need is to generate RSA key pairs and send public key to App to encrypt data...
Im trying to get SAADC to continuously sample using internal timer but im getting couple of samples and then it stops, tried everything but I'm obviously forgetting something...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
Hello,
I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
I'm using
the nRF52840 DK and the Matter light_bulb example, SDK v2.7.0.
a raspberry pi with the nRF dongle as a thread border router
the chip-tool running and compiled...
