Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello everyone,
I am doing some testing regaring advertising TX power on peripheral side with BLE.
I am using NCS version 2.6.1.
Hardware: nRF52840 Dev Kit
My...
I am trying to update our app from SDK 2.5.0 to 2.7.0 and it seems AWS MQTT has changed. We are building for the Thingy 91. The following lines are unrecognized.
CONFIG_AWS_IOT_CLIENT_ID_APP...
Hi ,
I need A small Assist from you , that i mentioned below .
Category: Bluetooth Mesh Network / Connectivity Issues.
Description:
I am encountering an issue with...
Hi everybody,
I need to send some user application configuration parameters to the nrf9160 on an nrf9160DK via the nrf52840 on the nrf9160DK. The client android application...
hello everyone,
I have a task to establish the connection between the BLE peripheral and mobile application after verifying the encryption by exchanging the public key of...
hello. I'm currently working on nRF connect for VS code and I'm having a problem.
After downloading the nRF connect for VS code extension, I'm having an issue with setting...
Dear all,
just some note upon this sample.
Using VS Code and copying sample app just not work due to some error into the path, missing file so I've try to adjust to get...
Hi,
I'm stuck with setting up device tree section about the TCA6416 and the associated C code.
the TCA6416 is connected to nrf9160 gpio P0.28 as interrupt active low....
Im building one project from
Works with SoftDevice S132 v7.2.0, provided with SDK 17.1.0. to
Works with SoftDevice S140 v7.2.0, provided with SDK 17.1.0. but upon...
Hello,
In the datasheet I could not find any reference for a device ID/whoami register for the npm1300. Is this feature missing? Is there another way to identify that the...
I downloaded the latest nef connect for desktop version. now I want to download and install the latest toolchain manager. when I try to open the current one I get this massage...
Dear Nordic Team,
We are currently developing a smart door lock using the nRF5340 and have started with the Matter lock sample demo code on our custom hardware.
To optimize...
hello Nordic
i am working with nrf52832, and nrf52840 with ncs v2.5.0
i am on the very adge of my ram take specially on the nrf52832 soc based devices.
we are working...
Hi,
We have a product based on the nRF5340 and have a Skyworks 66407 FEM which uses a simple 2 GPIO control scheme.
We have a shield configuration which enables the relevant...
I am running the Dev Academy Lesson 4 Exercise 2 - MQTT with TLS and getting the error:
[00:00:00.650,085] <err> nrf_modem: Modem has crashed, reason 0x4, PC: 0xecb64
...
