Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello, I'm a beginner and trying to do my project with nRF9151DK. As said this project uses the nRF9151DK that requires high-throughput USB-UART data streaming on two boards...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
Hello, I would like to evaluate the Thingy 91:X, but I can't install nRF Connect SDK on any machine (Windows / openSUSE) due to various problems. I will try to break down...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
My design is in alpha test and we just discovered that apparently SPIM allows only one module to be enabled at a time. When a second module (SPIM3, SPIM2) is enabled, the...
Tried 2 different wires on both Mac and windows pc. The device didn't show up in system information or Device Manager. NRF quickstart does not detect the device. When I connect...
Hello,
I’m trying to enable image encryption on nRF54L. When I enable the encryption, MCUBoot firmware size gets bigger and does not fit into 60kb region. When I set the...
Hi! I have a nRF52840 and an ESP32 and I want to perform a DFU to nRF52840 from ESP32, supposing I have the signed binary file in ESP32. I was already able to perform the...
Situation:
A FOTA job has been deployed in the cloud, so an update is ready and pending for a device.
Questions:
Once a device connects to nRF Cloud, how long should...
Hi,
I am working on developing Locator Tag using NCS fast pair sample code. I have one query here. Is Accurate RTC required for Google FMDN locator tag? If device loose...
Overal Goal & Problem
I'm struggling to port our nrf5 QSPI display driver to the nrf54L15's sQSPI. There is a lack of documentation and especially examples on using the...
Hello,
I use NCS 2.8.0 and toolchain 2.8.0 for my build. Also, the boad is a custom board with NRF52840.
My zephyr application is structured as show in this link : https...
Hi Nordic team, I received a Thingy91 sample last year, however on loading mfw_nrf91x1_2.0.2 and app: thingy91x_hello.nrfcloud.com_v2.0.2_debug.hex it is unresponsive and...
hi support team，
customer want to use 54L15 radio event
NRF_RADIO_EVENT_READY to set up gpio high ,and
NRF_RADIO_EVENT_DISABLED to clear gpio to low.
i tried below...
