Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I need to store a hardware-revision value on an nRF9160 during manufacturing (using something like nrfjprog ), and the non-secure application firmware must be able to read...
Hi
I’m working with an NPM1300EK connected over I²C to an nRF54L15 , and I’m seeing an issue where the VBUSINSTATUS register consistently reads back 0x00 , even when VBUS...
Hi,
I’m working on nRF9151 with nRF Connect SDK 2.9.0 , and I’m facing a FLASH overflow issue when enabling dual-image OTA (primary + secondary partitions) . Our project...
Issue Summary
fds_record_update() in SDK 13.0.0 creates permanent duplicate records instead of replacing old records. This causes:
Valid record count to grow indefinitely...
Hi Nordic support:
Our project uses the nRF9151 and QM13545 MIPI RF SWITCH. We have a question about AT%XMIPIRFFECTRL command's frequency: If the frequency switching point...
Hello,
I encountered a very strange problem. This problem originated from my development of RGB color lights using the NRF52840. Due to the limitations of RGB color lights...
If anyone has successfully stored and retrieved settings on the nRF52840 dongle using any method, please share your approach.
I'm trying to store and retrieve settings...
We are testing SPI communication with the nrf5340 Board as the mater and the nrf52840 board as the slave.
The FW applied to nrf5340 is a FW whose normal operation was confirmed...
I have a problem understanding notifications/subscriptions in the BLE context.
I have two devices, Central (nRF5340) and Peripheral (nRF52832). My peripheral provides a...
This not a question. It is for your information (FYI). I've seen many questions about flashing the nRF53 using CMSIS-DAP. Anyone interested see attached instructions.
The...
Using an approach similar to what's in the ble_app_att_mtu_throughput example, my goal is to transfer data as fast as possible. (I.e. call sd_ble_gatts_hvx() on the same characteristic...
I'm building the nrf/samples/openthread/cli sample with the nrf54l15dk/nrf54l15/cpuapp/ns board. The only change I'm making is enabling CONFIG_DEBUG_THREAD_INFO.
The app...
Hello,
I am using an LE audio code "nrf5340_audio" code from nRF SDK v2.8.0 to play a beep tone. I want to play a tone from a temporary memory, so I have created a logic...
I'm following the dev academy lessons and I'm having a bit of an issue where VS Code intellisense isn't picking up on the include paths from zephyr (e.g. #include <zephyr...
