Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
We have studied the getting started guide for the OTA upgrade at the link below.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development...
Hi all,
I was trying to evaluate the nRF52840 current consumption through the online power profiler. I set the tool as in the below image
there are three standby currents...
Hello guys,
I am attempting to send AT commands to an nrf9160 over UART. I started by loading the serial_lte_modem sample and sending commands using the LTE link monitor...
If I add
CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
to tests/crypto/prj.conf then CONFIG_ENTROPY_CC310=y gets turned off when building. By default, this will then cause a hard...
Hi
I am using the nrf52832 with the heart rate (freertos) example
Let say i want to add a new service and characteristic to that service ,this service is not suppose to...
Hi,
I have developed a simple system based around a Raspberry Pi Zero. The system uses a couple of sensors to measure temperature and water pressure using a ADS51115 A/D...
Hello,
I use NRF Connect Desktop on Windows 10 - 64 bits.
When I lauch the Programmer application with my NRF52 I have this issue :
2020-07-20T11:27:17.148Z ERROR Error...
Hi,
I am using the nRF5_SDK_13.1.0_7ca7556.
When I call the pm_conn_secure(), it returns NRF_ERROR_INTERNAL.
Can you tell me why did the NRF_ERROR_INTERNAL occur?
...
Hi ,
I followed the getting started steps and enabled the global sim. Now the LED 3 is blinking .
In the LTE Link Monitor , I see the following :
2020-07-22T03...
When I enable watchdog in main application by:
nrf_drv_wdt_config_t config = NRF_DRV_WDT_DEAFULT_CONFIG; err_code = nrf_drv_wdt_init(&config, wdt_event_handler); APP_ERROR_CHECK...
I'am currently porting an existing application that makes extensive use of the app_scheduler to FreeRTOS. To speed up the migration I have enabled the app_scheduler in the...
Hi,
I'm connecting a thingy91 to nrfCloud and visualizing data correctly. Anyway, only flip data is available in motion data.
How can I display orientation and acceleration...
Hello Nordic Team, a broad question and not sure if this is in the realm of possibility.
I have a test environment with a test client (python/pygatt) running on Linux with...
Hello All,
I was wondering if anyone would know if the nRF9160 is capable of LTE-M enhancement Mode B? (I'm in the US market)
If not, would you know an LTE-M product...
