If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
my nrf51822 QFABC1 not working BLE , i used sdk 12.3.0 and uploaded softdevice is s130, and also I upload
I attached my schematics diagram also
please support any mistake...
Hi,
We are writing an application for nrf5340 similar to rpmsg sample with zephyr. We see that the application encounters stack overflow issue when flashed on target...
Hi,
We are trying to synchronize time across 3 nrf5340, where one will be master and the other 2 nrf5340 will have to synchronize their time with the master.
1. All...
I had raised ticket " https://devzone.nordicsemi.com/f/nordic-q-a/63754/nordic-sdk-qspi-driver-call" .
Wanted help for using qspi driver with non blocking mode. I have modified...
Hello, does anyone tried terminated vs unterminated RF switch in AoA / AoD application? According to forum, some people use terminated switch, some don't.
Also, there should...
I've a prototype board which I need to externally program. The prototype board supplies it's own 3v supply to the chip (working fine) via a 5v supply which is current limited...
Hi,
I am using NRF52832 with SDK 17.0.0.
I wanna try to connect multiple devices with only one Android phone.
When I try demo on Samsung galaxy S8, I can connect with...
I am using SDK 14.01 and ble_app_beacon example in that, I want to send updated sensor data in advertising. Using ble_advdata_set() I am able to send the updated data in advertising...
SDK14.0+NRF52832: firstly I init the passkey in the function gap_params_init as above.I want to change the passkey and can save the new passkey to flash, but when I input...
Dear all, I want to measure the current consumption of my application on a nRF52833 DK. On top of that I want to be able to power the device using the VDDH and set the VDD...
Hello,
I am trying to run the A-GPS sample program but am encountering a bit of difficulty with the SUPL code.
I had to modify the LTE connection code to allow access...
Hello,
I am using nRF51422 DK running on SDK v12.3.0. I am migrating the project examples/ble_central/ble_app_uart project from Keil uVision to Segger Embedded Studio using...
Hi,
I am trying to toggle one pin via PPI when receiving event on another pin - code snippet below:
#include <stdbool.h> #include <stdint.h> #include "nrf.h" #include...
Hi,
What is the fast way to stream data from NRF52840
1) Using USB interface and virtual com (CDC)
2) Using UART interface and extenal converter as DTFI
Please Advise...
Hi,
I use SDK16 and S140 softdevice v7.0.1. I try to send a binary file from mobile to nRF52840 (PCA10056). I download examples\ble_peripheral\experimental\ble_app_ots project...
