Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
So I need to decrypt a single 16 byte block of data using AES128 and a pre-shared key on the above SoCs. But PSA doesn't seem to work (I'm currently working using the nRF52DK...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi team,
I'm using the NRF54L15DK board with NCS SDK v2.9.0.
I'm trying to include the B0 bootloader along with the MCUBOOT and application.
I'm wanted to customize...
As subject, the key is using prj.conf, compilation errors will occur, if do not use prj.conf, c ompilation pass but 54L15 not work(no logs aft pwer on). Is fast pair(locator...
Hi, I am currently migrating my project from nRF Connect SDK v2.5.3 to v2.9.0 / sysbuild.
Unfortunately, my devicetree configuration for a mcp2515 CAN interface is not accepted...
Hi, Nordic team
we want to develop indoor tracking system using nordic soc chip we saw some sample codes from your nordic sdk 2.9.0 , we need any research papers or documentation...
While experimenting with the v2.6.0 set of matter examples, it was noticed by an associate that the LightSwitch example doesn't seem to want to connect to any networks. This...
I am using NCS v2.9.1 and trying to enable a bootloader chain with NSIB and MCUboot. The regular setup works fine, however if I try to enable the minimal configuration, I...
Hello, just like the title indicated, I need help with setting up the nRF21540 EK with the nRF9160 DK.
For my application, since the nRF9160 DK has the nRF52840 on it, I...
Sorry for the inconvenience!
I have downloaded V2.8.0 nRF SDK, and I use this command to build light bulb project:
west build -p always --build-dir nrf/samples/matter...
Hi everyone,
I’m working on a project involving the nRF7002DK, where I’m trying to combine two separately working applications:
A TinyML CIFAR-10 image classification...
I am attempting to configure and build the Asset Tracker v2 for my Actinius Icarus v2 board.but the build is failing.
Setup:
nRF Connect SDK v 2.9.0
Board target:...
Hi,
I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
Hi, Any one kindly suggest and Chip based antenna for the Thread + BLE and Wi-Fi + BLE protocol in NRF54L15 protocol. Also kindly suggest the PCB based antenna for the Thread...
